301183
9
Zoom out
Zoom in
Previous page
1/12
Next page
9
L1a / IM-NORD En / A31008-M2001-R201-1-9W19 / AL140_IM-NORD_EN.fm / 09.09.2008
Care
Wipe the base station, charging cradle and handset
with a damp cloth (do not use solvent) or an anti-
static cloth.
Never
use a dry cloth. This can cause static.
Contact with liquid
If the handset has come into contact with liquid:
1. Switc
h off the handset and remove the bat-
tery pack immediately.
2. Allow the liquid to drain from the handset.
3. Pat all parts dry, then place the handset with
t
he battery compartment open and the keypad
facing down in a dry, warm place for at least
72 hours (no
t in a microwave, oven etc.).
4. Do not switch on the handset again until it is
co
mpletely dry.
When it has fully dried out, you will normally be
able to use it again.
Questions and answers
If you have any questions about using your phone,
visit us at
www.gigaset.com/customercare at any
time. The table below contains a list of common
pr
oblems and possible solutions.
Authorisation
This device is intended for analogue phone lines in
your network.
Country-specific requirements have been taken
in
to consideration.
We, Gigaset Communications GmbH, declare that
th
is device meets the essential requirements and
other relevant regulations laid down in Directive
1999/5/EC.
A copy of the 1999/5/EC Declaration of Conformity
is a
vailable at this Internet address:
www.gigaset.com/docs.
Problem Cause Solution
Nothing
appears in
the display.
The handset is not
turned on.
Battery pack is
fl
at.
Press the end call key
a for approx. 5 sec-
onds or p
lace the
handset in the base
station.
Charge/replace the
batt
ery pack (page 3).
No reaction
to key press.
The keypad lock is
ac
tivated.
Press the hash key
R
for approx. 2 sec-
onds (page 1).
No wireless
co
nnection to
the base sta-
tion, Ba
se
flashes in
the display.
The handset is
outsid
e the range
of the base sta-
tion.
The handset is not
r
egistered.
The base station is
n
ot turned on.
Cords not routed
corr
ectly.
Move the handset
closer t
o the base
station.
Register the handset
(page 3).
Check the power con-
nector at the base sta-
tion (page 2).
Check cord routing
(page 2).
You cannot
h
ear a ringer/
dialling tone
from the fixed
network.
The phone cord
sup
plied has not
been used or has
been replaced by
a new cord with
the wrong jack
connections.
Please always use the
ph
one cord supplied
or ensure that the jack
connections are cor-
rect when purchasing
fr
om a retailer
(page 2).
!
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
You have entered
the w
rong system
PIN.
Reset the system PIN
to the default 0000.
To do this, unplug the
mains unit from the
mains socket
£Press and hold the
paging key
£Plug the mains
adapter in again
£Hold the paging
key down for at least
another 2 seconds
and then release.
The reset procedure is
now
carried out.
The handsets are de-
registered. The calls
list is
cleared.
Problem Cause Solution
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens gigaset al145 trio at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens gigaset al145 trio in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens gigaset al145 trio

Siemens gigaset al145 trio User Manual - Dutch - 16 pages

Siemens gigaset al145 trio User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info