788205
49
Zoom out
Zoom in
Previous page
1/52
Next page
en Trouble shooting
48
3Trouble shooting
Tr oubl e shoot i ng
Faults often have simple explanations. Please read the
information and tips provided below before calling the
after-sales service.
Information, warnings and fault codes
In the event of a problem, information, warnings or fault
codes will automatically appear on the display. Follow
the instructions on the touchscreen display to rectify the
problem.
Notes
A fault code will also be displayed with some
warnings. If necessary, provide the after-sales
service with the fault code.
If a fault occurs, the appliance will not switch to
standby mode.
Tips
Problem Solution
The hob will not switch on. Use other electrical appliances to check whether a short circuit has occurred in
the power supply.
Make sure that you have connected the appliance as shown in the circuit diagram.
If you are unable to rectify the fault, contact our technical after-sales service.
The touchscreen display is not responding or has frozen. The control panel is damp or there is something on it. Dry the control panel or
remove the object.
The cooking zone's power level cannot be increased. The hob's total power output has been limited. Change the total power under Max-
imum power consumption in the basic settings.
If a very large item of cookware is being used, this may have an effect on the maxi-
mum power level for that half of the hob. Set the cookware down again.
An audible signal will sound if there is something on the touch-
screen display.
Remove the object and reconfigure the hob settings.
Do not place hot cookware on the control panel.
The hob is responding in an unusual manner or cannot be oper-
ated properly.
Switch the appliance off using the main fuse or the circuit breaker in the fuse box.
Wait a few seconds before reconnecting the appliance.
The electronics have overheated and have switched off the
affected cooking zone.
Wait until the electronics have cooled down sufficiently. When the fault indicator
goes out, you can continue cooking.
The electronics have overheated and all the cooking zones have
been switched off.
There is hot cookware near the control panel. The cooking zone
has been switched off to protect the electronics.
Remove the cookware that is causing the problem. Wait a few seconds. When the
fault indicator goes out, you can continue cooking.
The cooking zone has overheated and has been switched off to
protect the work surface.
Wait until the electronics have cooled down sufficiently. Then switch the cooking
zone on again.
The transfer settings function cannot be activated. You have removed the active item of cookware from its position and set a pot or
pan of a different size down instead. Test with the same item of cookware.
The hob has been operating continuously for an extended period. The automatic safety cut-out function has been activated. See the section entitled
~ "Automatic safety cut-out"
The activeLight light strips at the sides are not lighting up. Contact our technical after-sales service.
The cooking sensor has overheated and the cooking zone has
been switched off. E8202
Wait until the temperature sensor has cooled down sufficiently. Then reactivate
the function.
The cooking sensor has overheated and the adjacent cooking
zones have been switched off. E8203
If you are not using the cooking sensor, remove it from the cookware and keep it
away from other cooking zones or heat sources. Switch the cooking zones on
again.
The battery in the cooking sensor is almost flat. E8204 Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the
battery"
The connection to the cooking sensor has been broken. E8205 Switch the function off and then on again.
The cooking sensor is broken/faulty. E8206 Contact our technical after-sales service.
Trouble shooting en
49
Demo mode
If the ± symbol is shown on the display, demo mode
is active. The appliance does not heat up in demo
mode. Disconnect the appliance from the power
supply.Wait a few seconds before reconnecting the
appliance. Then deactivate demo mode in the basic
settings within 3 minutes of switching on the appliance.
The cooking sensor indicator will not light up and the cooking
sensor is not responding.
Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the
battery"
If this does not solve the problem, press and hold the symbol on the cooking sen-
sor for 8-10 seconds and then reconnect the cooking sensor to the hob. See the
section entitled ~ "Connecting the wireless temperature sensor to the control
panel"
If the problem persists, contact our technical after-sales service.
The indicator on the sensor flashes twice. The battery in the cook-
ing sensor is almost flat. You may be interrupted the next time you
cook by the battery running out.
Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the
battery"
The indicator on the sensor flashes three times. The connection
to the cooking sensor has been broken.
Press and hold the symbol on the cooking sensor for 8-10 seconds and then
reconnect the cooking sensor to the hob. See the section entitled ~ "Connecting
the wireless temperature sensor to the control panel"
The hob is unable to connect to your home network or the extrac-
tor hood. E7010
Switch the hob off and then on again.
If the message appears again, contact our technical after-sales service.
The operating voltage is incorrect and outside of the normal oper-
ating range. E9000/E9010
Contact your electricity supplier.
The hob is not connected correctly U400 Disconnect the hob from the mains. Make sure that you have connected the hob
as shown in the circuit diagram.
Problem Solution
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens EZ907KZY1E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens EZ907KZY1E in the language / languages: English as an attachment in your email.

The manual is 5.74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens EZ907KZY1E

Siemens EZ907KZY1E User Manual - German - 52 pages

Siemens EZ907KZY1E User Manual - Dutch - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info