790761
22
Zoom out
Zoom in
Previous page
1/28
Next page
en Troubleshooting
22
25.1 Warnings
Notes
¡If ⁠appears in the displays, press and hold the
sensor for the respective cooking zone and read the
fault code.
¡If the fault code is not listed in the table, disconnect
the hob from the power supply and wait 30seconds
before reconnecting it. If this display appears again,
contact the technical after-sales service and specify
the exact fault code.
¡If an error occurs, the appliance does not switch to
standby mode.
¡In order to protect the appliance's electronic parts
from overheating or surge currents, the hob may
temporarily reduce the power level.
25.2 Information on the display panel
Fault Cause and troubleshooting
No displays light up. The power supply has been disconnected.
Use other electrical appliances to check whether there has been a power failure.
The appliance has not been connected as shown in the circuit diagram.
Connect the appliance in accordance with the circuit diagram.
Electronics fault
If you are unable to rectify the fault, inform the technical after-sales service.
The displays flash. The control panel is wet or an object is covering it.
Dry the control panel or remove the object.
⁠ ⁠, ⁠ ⁠, ⁠ ⁠ ⁠ ⁠ ⁠,
⁠ ⁠ ⁠ ⁠ ⁠, ⁠ ⁠ ⁠ ⁠ ⁠
The electronics have overheated and one or all of the cooking zones have been switched
off.
Wait until the electronics have cooled down sufficiently. Then touch any button on the
control panel.
⁠ ⁠ + power level and
audible signal
There is hot cookware in the vicinity of the control panel. This may cause the electronics to
overheat.
Remove the cookware. The fault display goes out shortly afterwards. You can continue to
cook.
⁠ ⁠ and signal tone There is hot cookware in the vicinity of the control panel. The cooking zone has been
switched off to protect the electronics.
Remove the cookware. Wait a few seconds. Touch any button. When the fault display
goes out, you can continue cooking.
⁠ ⁠/ ⁠ ⁠ The cooking zone has overheated and has been switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently before switching the cooking
zone back on.
⁠ ⁠ flexMotion does not switch on.
Touch any button to confirm the fault display. You can continue to cook as normal
without using the flexMotion function. Contact customer service.
⁠ ⁠ flexInduction Plus does not switch on.
Touch any sensor to confirm the fault display. You can use the remaining cooking zones
to continue cooking. Contact the technical after-sales service.
⁠ ⁠ The cooking zone has been operating continuously for an extended period.
Individual safety switch-off is switched on. Touch any button to switch off the display so
that you can set the cooking zone again.
⁠ ⁠ ⁠ ⁠ ⁠/ ⁠ ⁠ ⁠ ⁠ ⁠ The operating voltage is incorrect and outside of the normal operating range.
Contact your energy supplier.
⁠ ⁠ ⁠ ⁠ The hob is not connected correctly.
Disconnect the hob from the mains. Connect the hob in accordance with the circuit dia-
gram.
⁠ ⁠ Demo mode is activated.
Disconnect the hob from the mains. Wait for 30 seconds and connect the hob. Touch
any sensor in the next threeminutes. Demo mode is deactivated.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens EX807NYV6E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens EX807NYV6E in the language / languages: English as an attachment in your email.

The manual is 1.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens EX807NYV6E

Siemens EX807NYV6E User Manual - German - 28 pages

Siemens EX807NYV6E User Manual - French - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info