790955
49
Zoom out
Zoom in
Previous page
1/56
Next page
Trouble shooting en
49
3Trouble shooting
Tr oubl e s hoot i ng
Faults often have simple explanations. Please read the
information and tips provided below before calling the
after-sales service.
Information, warnings and fault codes
In the event of a problem, information, warnings or fault
codes will automatically appear on the display. Follow
the instructions on the touchscreen display to rectify the
problem.
Notes
A fault code will also be displayed with some
warnings. If necessary, provide the after-sales
service with the fault code.
If a fault occurs, the appliance will not switch to
standby mode.
Tips
Cleaning
How do I clean the hob?
Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-
water detergent (concentrated) or scouring pads.
You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning"
Problem Solution
The hob will not switch on. Use other electrical appliances to check whether a short circuit has occurred in the
power supply.
Make sure that the appliance has been connected as shown in the circuit diagram.
If the fault cannot be rectified, inform the technical after-sales service.
The touchscreen display is not responding or has frozen. The control panel is damp or there is something on it. Dry the control panel or remove
the object.
The cooking zone's heat setting cannot be increased. The hob's total power output has been limited. Change the total power under "Maxi-
mum power consumption" in the basic settings.
If a very large item of cookware is being used, this may have an effect on the maxi-
mum heat setting for that half of the hob. Place the cookware back on the hob.
An audible signal sounds when there is an object on the touch-
screen display.
Remove the object and reset the hob.
Do not place hot cookware on the control panel.
The hob responds in an unusual manner or cannot be oper-
ated properly.
Switch the appliance off using the main fuse or the circuit breaker in the fuse box.
Wait a few seconds before reconnecting the appliance.
The electronics have overheated and have switched off the
affected cooking zone.
Wait until the electronics have cooled down sufficiently. When the fault code on the
display goes out, you can resume cooking.
The electronics have overheated and all the cooking zones
have been switched off.
There is hot cookware near the control panel. To protect the
electronics, the cooking zone has been switched off.
Remove the cookware that is causing the problem. Wait a few seconds. When the
fault code on the display goes out, you can resume cooking.
The cooking zone has overheated and has been switched off
to protect the work surface.
Wait until the electronics have cooled down sufficiently before switching the cooking
zone back on.
The transfer settings function will not activate. Acknowledge the fault code by touching any of the buttons. You can cook as usual
without using the transfer settings function. Contact the technical after-sales service.
The FlexPlus cooking zone will not activate. Acknowledge the fault code by touching any of the buttons. You can use the other
cooking zones to cook as usual. Contact the technical after-sales service.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens EX801KYW1E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens EX801KYW1E in the language / languages: English as an attachment in your email.

The manual is 5.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens EX801KYW1E

Siemens EX801KYW1E User Manual - German - 60 pages

Siemens EX801KYW1E User Manual - Dutch - 56 pages

Siemens EX801KYW1E User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info