788231
6
Zoom out
Zoom in
Previous page
1/16
Next page
en Operating the appliance
6
Combination cooking zone
The single and dual-circuit hotplate can be operated
without the bridge heating element independently of
each other or combined with the bridge heating
element as described in the table.
The small roasting zone (1 + 3) and the single-circuit
hotplate (2) can also be operated independently of
each other with different heat settings. Different
temperature ranges are therefore generated at the large
roaster, the teppan yaki or the grill plate, for example:
the small roasting zone can then be used to fry a meal
and the single-circuit hotplate can simultaneously be
used to keep a meal warm.
Note: Suitable cookware is available from the after-
sales service or our e-Shop.
Residual heat indicator
The hob has a two-stage residual heat indicator for
each hotplate.
If appears in the display the hob is still hot. It may be
used, for example, to keep a small meal warm or to
melt cooking chocolate. As the hotplate cools down
further, the display changes to œ. The display remains lit
until the hotplate has cooled sufficiently.
1Operating the appliance
Oper at i ng the appl i ance
In this section, you can find out how to set the
hotplates. The table shows heat settings and cooking
times for various meals.
Switching the hob on and off
The main switch is used to switch the hob on and off.
Switching on the appliance
Touch the # symbol. A signal sounds. The indicator
light above the main switch lights up. The control
displays and the heat setting displays light up. The
hob is ready for use.
The two front hotplates are automatically selected. The
heat setting displays light up brightly.
Switching off the appliance
Touch the # symbol until the indicator light above the
main switch and the displays go out. All hotplates are
switched off. The residual heat indicator remains on
until the hotplates have cooled down sufficiently.
Notes
The hob will switch itself off automatically once all
hotplates have been switched off for a while (10-
60 seconds).
The settings remain stored for 4 seconds after the
hob has been switched off. If you switch it on again
during this time, the hob will operate using the
previously stored settings.
Setting a hotplate
Select the desired heat setting on the control panel.
Heat setting 1 = Lowest power
Heat setting 9 = Highest power
Every heat setting has an intermediate setting. It
appears on the display, e.g. as ..
Selecting the heat setting
The hob must be on.
1. Touch the heat setting display to select the
hotplate.
lights up brightly on the heat setting display
2. Select the required heat setting on the control panel.
The hotplate is switched on.
Changing the heat setting:
Select the hotplate and set the required heat setting on
the control panel.
Switching off the hotplate
Select the hotplate. Set the control panel to 0. After
about 10 seconds, the residual heat indicator appears.
Note: The last selected hotplate remains activated. You
can set the hotplate without selecting it again.
1 = dual-circuit hotplate
2 = single-circuit hotplate
3 = bridge heating element
Combination Activation Suitable for
Small roasting
zone:
Combination of 1
+ 3
With the ˆ symbol activate
the bridge heating element.
ˆ symbol lights up
brightly.
Small roaster
Small teppan yaki
Large roasting
zone:
Combination of 1
+ 3 + 2
Touch the Ô symbol
Ô symbol lights up brightly.
Large roaster
Large teppan yaki
Large grill plate
E
12
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens ET875LMP1D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens ET875LMP1D in the language / languages: English as an attachment in your email.

The manual is 1.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens ET875LMP1D

Siemens ET875LMP1D User Manual - German, Dutch, French, Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info