Manual Siemens ER926SV70N (page 6 of 20) (English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish)

527448

Zoom out

Zoom in

1/20

Read the appliance's instructions before

installing and using.

The graphics in these Assembly

instructions are given as a guide only.

The manufacturer is exempt from all

liability if this manual's requirements

are not complied with.

Safety instructions

All operations relating to installation,

regulation and conversion to other

types of gas must be carried out by

an authorised installation engineer,

respecting applicable regulations,

standards and the specifications of

the gas and electricity providers.

Before you begin, turn off the

appliance's electricity and gas

supply.

You are recommended to contact the

Technical Assistance Service to

convert to another type of gas.

This appliance has been designed for

home use only, not for commercial or

professional use. This appliance cannot

be installed on yachts or in caravans.

The warranty will only be valid if the

appliance is used for the purpose for

which it was designed.

Before installing, you need to check that

local distribution conditions (gas type

and pressure) and the appliance's

adjustment are compatible (see table I).

The appliance's adjustment conditions

are written on the label or the

specifications plate.

This appliance can only be installed in a

well-ventilated place in accordance with

existing regulations and ventilation

specifications. The appliance must not

be connected to a combustion product

evacuation device.

The supply cable must be attached to

the unit to prevent it from touching hot

parts of the oven or hob.

Appliances with electrical supply must

be earthed.

Do not tamper with the appliance's

interior. If necessary, call our Technical

Assistance Service.

Before installing

This appliance is class 3 type, according

to the EN 30-1-1 regulation for gas

appliances: built-in appliance.

The units next to the appliance must be

made of non-flammable materials. The

laminated covering and glue for

adhering it must be heat resistant.

This appliance cannot be installed

above fridges, washing machines,

dishwashers or similar.

An oven must have a power cooling fan

to install a hob above it.

Check the oven's dimensions in its

installation manual.

If an extractor fan is installed, you must

follow the installation manual's

instructions, always keeping a minimum

distance of 650 mm to the hob.

Preparation of kitchen unit

(fig. 1-2)

Make an appropriate size cut in the work

surface.

If the hob is electric or mixed (gas and

electricity) and there is no oven below,

place a non-flammable separator (e.g.

metal or plywood) 10 mm from the

bottom of the hob. This will prevent

access to the base of the hob.

If the hob is gas, it is recommendable to

place the separator at the same

distance.

On wood work surfaces, varnish the

cutting surfaces with a special glue. This

protects them from moisture which could

collect under the work surface.

Installation of appliance

The clips and the adhesive seal

(underside of the hob) are factory-fitted:

do not under any circumstances remove

them. The seal ensures that the entire

work surface will be watertight, and

prevents water seepage.

In order to fit the appliance into the

kitchen unit, first place the hob in the

correct position then loosen each of the

clips so that they all turn freely (it is not

necessary to completely undo them).

Insert and centre the hob.

Press the sides of the hob until it is

supported around its entire perimeter.

Turn the clips and tighten them fully.

Fig. 3

Removal of hob

Turn off the appliance's electricity and

gas supply.

Unscrew the clips and proceed in the

reverse order to installation.

Gas connection (fig. 4)

The end of the inlet connection point of

the gas hob has a 1/2” (20.955 mm)

thread that allows for:

- fixed connection.

- connection using a flexible metal pipe

(L min. 1 m - max. 3 m)

. In this case, it is

necessary to insert the accessory

(427950) and the watertight seal

(034308) supplied between the manifold

outlet and the gas supply. Fig. 4a.

In this case, you must prevent the pipe

from coming into contact with moving

parts of the kitchen unit being inserted

(for example, a drawer) and prevent

access to any spaces which might

become obstructed.

If you need to connect the gas supply

horizontally, our Technical Assistance

Service can supply you with an L-tube

(code 173018) and a seal (code

034308). Fig. 4b.

Warning! If any connection is handled,

check the seal.

Danger of leaks.

The manufacturer is not liable for any

connection leaking, after being handled.

Electric connection (fig. 5)

Check that the voltage and power of the

appliance are compatible with the

electrical installation.

The hobs are supplied with a power

cable with or without a wall socket plug.

Provide an omnipolar cut-off switch with

a minimum contact separation of 3 mm

(except for plug connections, if the user

has access to it).

Appliances with plugs must only be

connected to sockets that have earth

wires correctly installed.

This appliance is type “Y”: the supply

cable can only be changed by the

Technical Assistance Service and not

the user. The cable type and minimum

cross-section must be respected.

Changing the gas type

If the country's regulations allow, this

appliance can be adapted to other types

of gas (see specifications plate). The

components required for this are in the

transformation kit supplied (depending

on the model) available from our

Technical Assistance Service. The

following steps should be taken:

A) Changing the nozzles of the rapid,

semi-rapid and auxiliary burners on

the hob (fig. 6):

- Remove the pan supports, burner

covers and diffusers.

- Change the nozzles using the spanner

provided by our Technical Assistance

Service (code 424699), taking special

care to ensure that the nozzle does not

fall when it is removed from the burner or

when fitted.

Ensure that it is completely tightened in

order to guarantee the seal. Primary air

adjustment is not necessary with these

burners.

B) Changing the nozzles for double-

flame burners (fig. 7):

The glass panel and frame are fixed to

the rest of the hob using a clip mounting

system. The following steps must be

taken to remove the glass panel and

frame:

- Remove all the burner covers and pan

supports. Fig. 7a.

- Release the front clip fixing the

appliance to the kitchen unit by

removing the screw. Fig. 7b.

- Loosen the screws on the burners,

fig. 7c-7d, and remove the control knobs

from their respective housings.

Use the disassembly lever 483196

available from our Technical Assistance

Service. To release the front clips, apply

the lever in the area shown in figures 8

according to the hob model.

Never use the lever on glass edges

which have no trim or frame!

- To release the rear clips, carefully raise

the entire glass panel and frame, as in

fig. 8a.

Changing the outer flame nozzle

(fig. 9a):

- Loosen the clamp screw to release the

bushing by moving it backwards to

access the main nozzle easily. Fig. a1.

- Remove the outer flame nozzle by

turning it towards the left. Fig. a2-a3.

- Screw in the new outer flame nozzle.

Fig. a3-a4, as in table II.

- Adjust the distance of the airflow

adjusting bushing L2 according to the

value -Z- shown in table II. Fig. a5.

- Tighten the clamp screw. Fig. a6.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens ER926SV70N in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens ER926SV70N

Siemens ER926SV70N User Manual - Dutch - 11 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens ER926SV70N Manual

Product: