Please detach and keep
Instructions for the inst
Before connecting the appliance to the
supply
plate.
This appliance must be installed in a place
with the proper level of ventilation. The gases
produced during combustion must be released
to the outside.
Check the size of the hob and the size of
the opening to be made on the kitchen unit.
The panelling on the work surface in the
immediate vicinity of the hob must be made of
non-flammable material. Both stratified coatings
and the adhesive used to fix them in place
must be heat resistant. Otherwise, they may
be damaged.
Electric wiring must not come into contact
with hot areas
The mains supply cable must be fixed to
the kitchen unit to prevent it from coming into
contact with hot parts on the oven or hob.
Appliances with electric components must
be earthed.
Handle the appliance with care throughout
the entire installation process.
the appliance.
This appliance shall be installed in
accordance with the regulations in f
and only used in a well v
Read the instructions before installing or
using this appliance.
SHOULD THE RELEV
NOT BE PROPERL
INST
MANUF
Installing the hob in the
kitchen unit
Housing measurements
1- Minimum Distances (mm). Cut a hole of
the necessary size in the work surface, Fig. 1.
If it is to be installed over an oven, you must
and check the dimensions as given in the
installation manual.
Centre the hob in the hole on the work
surface.
2- The wood fibres used in the manufacture
of kitchen work surfaces are liable to swell
when they come into contact with moisture.
Y
edges with a special adhesive to protect them
from steam or condensed water which could
deposit beneath the work surface on the kitchen
unit.
Depending on the model purchased, the
fixtures and the watertight seal (lower edge of
the hob) may come factory-fitted. If this is the
case, do not under any circumstances remove
them. The seal keeps the entire work surface
watertight and prevents leakage.
If these parts are not factory-fitted, fix the self-
adhesive seal supplied with the appliance to
The end of the input collector on gas
hobs comes with a
1
/
2
L-tube from its factory-set position.
T
to remove the L-tube mounted in the factory
and assemble the one supplied in the accessory
bag. Fig. 4a. Do not forget to insert the seal.
If, for some reason, the L-tube should be twisted,
it is necessary to make sure that this area is
properly sealed. Make sure that all connections
performed are free of leakage.
The manufacturer does not accept any
liability for leakage on connections performed
by the installer or if the L-tube is moved or
twisted.
Check the voltage and total power on
the characteristics plate. The appliance must
be EARTHED.
Make sure that connection has been
performed in accordance with legal regulations
in force for the country in question. Comply
fully with the conditions laid down by the local
electricity company
In order to meet normal safety standards,
the installer must supply an all-pole circuit
breaker with a contact aperture of at least 3
mm. This is not necessary when connection is
made via a socket, so long as this is accessible
to the user
Appliances equipped with plugs should
only be connected to sockets which are duly
earthed.
The appliance is type "Y". This means that
the input supply cable cannot be changed by
the user. Only the brand's service technicians
are qualified to replace this cable. Use the right
cable type and section.
Do not tamper inside the appliance. If
necessary
Hobs with control knobs are supplied with
a plugged or unplugged power cable.
TYPES OF CABLE
All gas 3 x 0.5 mm
2
process, you must place the diffusers and the
tops of the burners on their corresponding
burners.
Changing the type of gas
supply
gas in question. Our hobs leave the factory set
for the gas type indicated on the characteristics
plate.
Depending on the regulations in force in
your country
with other types of gas (see characteristics
plate). T
follows:
1 -Remove the grates, covers and burner
2 -Change the injectors using a 7-mm
socket wrench and be sure to tighten them
down properly so that they are fully air-tight.
Fig. 6.
It is not necessary to adjust the primary air
on these burners.
B )
the burner valves.
1 - Set the valves to minimum.
2 - Remove the control knobs from the
valve shafts. Fig. 7.
4 -Adjusting the by pass screw
be tightened down fully.
clockwise direction until the correct release of
gas is reached: when the burner is changed
from the maximum to minimum settings, the
5 - Re-assembling the anti-liquid seals.
the water-tightness of the electricity system
against the spillage of liquids on the hob.
6 - Re-assemble the control knobs.
C) Put the label which indicates the type of
gas the appliance has been adapted to near
the characteristics plate.
.
t
3 -
flame does not go out or backfire
accessories bag and screw them into the lower
For disassembly
proceed in the reverse manner
Once the hob is fitted you should turn the clip
and
Remove the clips from the attached
poi
tigh
3-
4-
If the cooking hob is to be installed
power
dimensions according
ventilation, and check the
above an oven, check that the oven is fitted
with
to the assembly
manual.
Before connecting the appliance to the
5- In order to complete the installation
For Propane and Butane Gas: the screw must
For Natural Gas: turn the screw in an anti-
The option
unit (in accordance with the regulation for gas
appliances EN 30-1-1 ) is Type .
If no oven is installed under an electrical or
mixed (gas and electric) hob, place a
separator of non-flammable material e.g.
plywood or metal at a distance of 10 mm.
from the bottom of the hob to prevent access
to the lower part of the hob.
If no oven is installed under a gas hob, it is
suggested to place a separator of non-
flammable material e.g. plywood or metal at
a distance of 10 mm. from the bottom of the
hob to prevent access to the lower part of the
hob.
In the event that a drawer is located beneath
the appliance, please make sure that the
drawer contains no heat-sensitive or easily
combustible objects, such as spray cans or
shoe polish. Use a heat-resistant utility drawer
only
Power cable:
Do
A
core.
.
check that the oven is sufficiently well ventilated
”
correc tly on their supporting elements. Fig. 5.
en
the
characteristics
factory set
gas in question.
(Table I).
Our hobs leave the
for the gas type indicated on
(Table II).
All installation, regulation and adaptation to
other types of gas
authorised i
respecting a
standards and the count
gas supply compan
It is recommended
Technica
to other types of gas
off the applian.
All installation, regulation and adaptation to
other types of gas
authorised i
respecting a
standards and the count
gas supply compan
It is recommended
Technica
to other types of gas
off the applian.
Fig. 4. This caters for:
(20,955 mm)
threaded L-tube,
Rigid connection.
In either of the cases, do not move or twist the
(L min. 1m - max. 3m).If this method is used,
moving parts on the housing (e.g. drawers)
Connection to a flexible metal tub
and passing the tube through spaces liable
avoid both contact between this tube and
to get blocked.
valve.
in the event of damage, change the entire
the seals must be in place in order to ensure
Never dismount the valve shaft (Fig. 9):
