528366
17
Zoom out
Zoom in
Previous page
1/160
Next page
13
en
Water filter
A new water  lter must be rinsed before it
can be used.
To do this, press the water  lter  rmly
into the water tank 11 with the aid of the
measuring spoon 14. Fill the water tank
with water up to the “max” mark.
Turn the rotary knob 6 to select start
and press the start button 8.
Place 1 l container
Place suction pipe in container
start
Place a container with a capacity of 1 litre
under the milk frother 10.
Place the end of the suction pipe 10d in
the container.
Press the start button 8. Water will now
ow through the  lter to rinse it.
Next, empty the container.
The appliance is ready for use again.
Info: Rinsing the  lter simultaneously
activates the setting for the “change  lter”
display.
You can  nd detailed information about the
water  lter in the enclosed  lter instructions.
The  lter is no longer effective when the
Service - change filter display appears,
or at the latest after two months. It needs to
be replaced for reasons of hygiene and so
that there is no build-up of limescale (this
could damage the appliance).
Replacement  lters can be obtained from
retailers (TZ70003) or from customer
service (575491).
If no new  lter is used, turn the Water
filter setting to no.
Info: If the appliance has not been used for
a prolonged period (for example, when you
are on vacation), the existing  lter should
be rinsed before the appliance is used
again. To do this, simply dispense a cup of
hot water.
Transport. lock
To avoid damage caused by frost during
transport and storage, the appliance must
be completely emptied  rst.
Info: The appliance must be ready for use
and the water tank 11 lled.
Press the start button 8. The appliance
automatically empties the pipe system
and switches off.
Empty the water tank 11 and the drip
tray 23.
Factory reset
You can cancel your own settings and reset
the factory settings.
To activate the factory settings, press the
start button 8.
Info: The appliance can also be reset to
the factory settings using a combination of
buttons. The appliance must be switched
off fully.
Hold down the selection buttons < and
> 4 and the on/off switch 1 O / I at the
same time for at least 5 seconds. Press
the start button 8. The factory settings
are now reactivated.
TE803_806_1RW.indb 13 08.05.2013 14:24:10
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens EQ8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens EQ8 in the language / languages: English, Dutch, French, Polish as an attachment in your email.

The manual is 14,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens EQ8

Siemens EQ8 User Manual - German, Italian - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info