788241
33
Zoom out
Zoom in
Previous page
1/40
Next page
Trouble shooting en
33
3Trouble shooting
Tr oubl e s hoot i ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
If appears on the display, press and hold the
button for the relevant cooking zone in order to read
the fault code.
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Display Possible cause Solution
None The power supply has been disconnected. Use other electrical appliances to check whether a short circuit
has occurred in the power supply.
The appliance has not been connected as shown
in the circuit diagram.
Ensure that the appliance has been connected as shown in the
circuit diagram.
Electronics fault. If you are unable to rectify the fault, inform the technical after-
sales service.
The displays flash. The control panel is damp or there is something
on it.
Dry the control panel or remove the object.
The Ù display flashes in the
cooking zone displays.
A fault has occurred in the electronics. To acknowledge the fault, briefly cover the control panel with
your hand.
The active carbon filter is saturated or the satura-
tion indicator lights up even though the filter has
been cleaned or replaced.
Change the filter and reset the filter saturation indicator. You can
find additional information about this in section ~ "Cleaning".
”ƒ The electronics have overheated and have
switched off the affected cooking zone.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
”… The electronics have overheated and all of the
cooking zones have been switched off.
Ӡ + power level and audible
signal
There is hot cookware near the control panel.
There is a risk that the electronics will overheat.
Remove the cookware that is causing the problem. The fault dis-
play goes out shortly afterwards. You can continue cooking.
Ӡ and audible signal There is hot cookware near the control panel.
The cooking zone has been switched off to pro-
tect the electronics.
Remove the cookware that is causing the problem. Wait a few
seconds. Touch any touch control. When the fault indicator goes
out, you can continue cooking.
”‚/”‡ The cooking zone has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently. Then
switch the cooking zone on again.
”‰ The cooking zone has been operating continu-
ously for an extended period.
The automatic safety cut-out function has been activated. You can
find additional information about this in section .
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect and outside of
the normal operating range.
Contact your electricity supplier.
—…‹‹ The hob is not connected correctly. Disconnect the hob from the mains. Ensure that the hob has been
connected as shown in the circuit diagram.
Do not place hot cookware on the control panel.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens ED877FQ25E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens ED877FQ25E in the language / languages: English as an attachment in your email.

The manual is 3.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens ED877FQ25E

Siemens ED877FQ25E User Manual - German - 28 pages

Siemens ED877FQ25E User Manual - Dutch - 28 pages

Siemens ED877FQ25E User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info