652209

Siemens DO10802CHM Manual

8
Zoom out
Zoom in
Previous page
1/28
Next page
8
en
Congratulations on purchasing this Siemens appliance. You
have acquired a top-quality product, which will give you a lot
of enjoyment.
Please read this installation and operating instruction
manual carefully, then act accordingly! Store for future
reference.
Installation
(for the qualified professional)
Unpacking
■ Inspect the new appliance for transport damage!
■ Please dispose of the packaging, and if applicable, the old
appliance in an environmentally-friendly manner.
Install the small water heater as shown in the illustra-
tions. Observe the instructions in the text.
The illustrations can be found in the centre of the instruction
manual.
A
Scope of delivery/Dimensions
Undersink appliance DO10702M,
DO10702CHM
B
Water connection
■ Caution!
Do not allow the existing tap mixer to become calcified.
A reduced flow rate will ruin the water heater.
C
Wall mounting
■ For mounting without the wall hooks, observe the differ-
ent dimensions!
D
Screwing on the Connection Hoses
■ Fit the sealing gasket.
■ Place the sleeve nuts onto the threads and screw on by
hand.
■ Tighten the screw fitting.
Hold the threaded fittings on the water heater with a
spanner. Do not lubricate the thread!
■ After the unit has been used to heat water a few times,
retighten the screw fitting.
Replacement for a damaged threaded fitting is available from
customer service.
Oversink appliance DO10802M,
DO10802CHM
E
Wall mounting
■ For mounting without the wall hooks, observe the differ-
ent dimensions!
F
Connecting the tap mixer
G
Water connection
■ Caution!
Do not allow the existing tap mixer to become calcified.
A reduced flow rate will ruin the water heater.
■ Insert the connection pipes into the tap mixer.
■ Hang the water heater on the wall.
■ Screw the connection pipes onto the heater and the
tap mixer.
Hold the threaded fittings on the heater with a spanner.
Do not lubricate the thread!
H
First start-up
Electrical connection
■ Important: Do not insert the plug into the mains socket yet.
DO10702M, DO10702CHM only:
■ Open the corner valve.
■ Completely fill the heater’s reservoir with water.
■ Set the flow on the corner valve:
10-litre unit: 10 l/min = 1 l in 6 seconds
DO10802M, DO10802CHM only:
■ Set the flow with the adjustment screw on the tap mixer:
10-litre unit: 10 l/min = 1 l in 6 seconds
■ Only then insert the plug into the mains socket.
Checking the heating
■ Turn the rotary selector switch to “III” (approx. 85 °C).
■ Monitor the heating process until the pilot lamp
switches off.
Heating time:
10-litre unit: 25–35 minutes
■ Check the temperature.
■ Caution: If the safety temperature limitation has switched
off the small water heater, unplug the mains plug, open
the warm water tap and allow approx. 4 litres of water to
flow. Then plug the mains plug back in.
The appliance is ready again for operation.
Limitation of the water temperature
The temperature of the water leaving the tap for the small
water heater can be mechanically set to stage “I” (approx.
40 °C) or stage “e” (approx. 60 °C).
Information on temperature limiting can be found in the
operating instructions.
Saving energy
■ Turn the rotary selector switch to “e”.
■ Hand over the installation and operating instructions to
the user and explain how the appliance operates.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens DO10802CHM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens DO10802CHM in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info