Manual Siemens DH12400M (page 9 of 76) (English, German, Dutch, French, Polish, Portuguese, Spanish)

652238

Zoom out

Zoom in

1/76

Congratulations on purchasing this Siemens appliance. You

have acquired a top-quality product, which will give you a lot

of enjoyment.

Please read this installation and operating instruction

manual carefully, then act accordingly! Store for future

reference.

Installation instructions

Install the continuous-ﬂow heater as described in the

illustrated section. Observe the instructions in the text.

The illustrations can be found in the centre of the instruction

manual.

Installation

Unpacking/removing the cover

■ Unpack the appliance and check for transport damage.

■ Dispose of the packaging and, where applicable, the old

appliance, in an environmentally conscious manner.

II.

Preparation for installation

Important: Only use the enclosed installation set.

■ Shut off water supply. The electrical connection (connec-

tion cable) must be disconnected from the power supply.

Unscrew the fuse or switch off the circuit breaker.

III.

Wall mounting

■ The continuous-ﬂow heater must be ﬁtted securely to

the wall. If required, secure the appliance using the lower

adjusting screws.

■ The distance from the wall is variable. This allows you to

compensate for any unevenness in the wall surface.

■ The sleeve must ﬁt tightly round the connection cable. If

the sleeve is damaged during installation, the holes must

be sealed water-tight.

IV.

Water connection

■ The continuous-ﬂow heater must be vented. Open the

warm water tap fully and ﬂush out the appliance thorough-

ly for 1 minute.

■ The ﬂow-rate limiter must be installed in the old water

regulating valve.

Electrical connection

■ The electrical supply terminal can be ﬁtted at the top or

bottom. The sheath of the connection cable must extend

for at least 40 mm into the appliance.

Installation note

■ The installation of non plug-in ready appliances must be

undertaken by the respective utility operator or by a quali-

ﬁed specialist company, who can also assist you when

you are requesting the approval of the utility company for

installation of the appliance.

VI.

Startup

The device is compliant to IEC 61000-3-12.

■ At low water pipe pressure, check whether the II setting

switches on even when water is drawn from several cold-

water taps simultaneously. If not, remove the ﬂow limiter

(refer to additional information A).

■ Instruct the user with regard to the operation of the con-

tinuous-ﬂow heater.

A B

Additional information

■ If the water pressure of the interior system is low, do not

operate the continuous-ﬂow heater at full power, but re-

move the ﬂow limiter (Fig. A, 3.).

■ Priority circuit for the combined operation of electric stor-

age heaters (Fig. B).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Siemens DH12400M in the language / languages: English, German, Dutch, French, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 4,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Siemens DH12400M Manual

Product: