652229

Siemens DH12103M Manual

9
Zoom out
Zoom in
Previous page
1/44
Next page
9
en
Congratulations on purchasing this Siemens appliance. You
have acquired a top-quality product, which will give you a lot
of enjoyment.
Please read this installation and operating instruction
manual carefully, then act accordingly! Store for future
reference.
Installation instructions
Install the continuous-flow heater as described in the
illustrated section. Observe the instructions in the text.
The illustrations can be found in the centre of the instruction
manual.
Installation
I.
List of items supplied
1 Continuous-flow heater
2 Installation template
3 Connection piece for hot water
4 Washer, red Ø 15 mm
5 Connection piece for cold water
6 Washer, Ø 24 mm
7 Mounting bolt
8 Wall plug
9 Securing nut
10 Threaded bushing
11 Cable grommet
II.
Wall mounting
There are two ways in which the continuous-flow heater can
be mounted on the wall:
– Using the mounting bolt. Unevenness in the wall up to a
depth of 25 mm can be compensated for.
– Making use of the holes that were drilled for the old heater:
Use the mounting template to establish whether the exist-
ing holes line up properly.
The following describes the installation procedure using the
mounting bolt.
Marking the point for mounting the heater and selecting
the opening for the connecting cable (Fig. A)
Important!
Make sure that the connecting cable is isolated
from the mains electricity supply!
■ Place hole 3 in the mounting template over the cold-water
inlet.
■ Select the most suitable hole through which the connect-
ing cable is be fed. The connecting cable must pass through
one of the six holes marked 14... Terminal BZ45Z20M can
be used if the cable is fed into the continuous-flow heater
through one of the bottom holes marked 14a.
■ Mark the point 12 at which the mounting bolt is to be
inserted.
Fitting the mounting bolt and attaching the pipe
connecting pieces (Fig. B)
Open up the heater (Fig. C)
Punching out the holes at the rear of the heater for the
mounting bolt and the connecting cable
Important: When mounting the appliance, only the holes
actually required should be punched out. Any other holes
that are not going to be used must be sealed watertight.
Inserting the connecting cable (Fig. D)
■ Push the grommet 11 over the end of the connecting cable.
Note: Do not use the grommet for a cable with a cross-sec-
tion of 16 mm
2
. The appliance must then be installed flush
with the wall.
Attention: Without a grommet, the DH12103M is splash-
proof only (IP 24).
■ Place the heater over the connecting cable.
■ Press the grommet into the hole in the rear wall of the
heater through which the cable should be fed. Ensure that
the edges of the grommet are flush with the hole all the
way round.
■ Fit the heater onto the threaded bushing 8 and secure it
in place with the nut 9.
Compensating for unevenness in the wall (Fig. E)
III.
Water connection
■ Using the locking screw 15, the water connection can be
aligned by ± 10 mm vertically.
■ Adapt the bend in the “hot” pipe so that it lines up with
the hot-water outlet. In doing so, make sure that the
“cold” elbow connection is not bent.
Attention: Ensure that a distance of at least 6 mm is main-
tained to live parts of the heater.
■ Connect the water outlet and inlet and tighten the secur-
ing nut on the mounting bolt.
Checking for leaks and flushing the heater:
■ Turn on the hot-water tap.
■ Check that all pipe joints are properly sealed.
■ The mixer and the warm water pipe may
be hot. Please inform and instruct children
appropriately.
■ Do not use aggressive or abrasive cleaning
detergents!
■ Do not use a steam cleaner.
■ The appliance is only to be descaled by a
suitably qualified specialist.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens DH12103M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens DH12103M in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info