652223

Siemens DE2427527M Manual

8
Zoom out
Zoom in
Previous page
1/24
Next page
8
en
A fault, what to do?
Attention!
Repairs must only be carried out by an authorised technician. Improper repairs can lead to risk of serious injury to
the user.
If your appliance does not operate as required, it is often due to a very minor problem. Please check whether you can remedy
the fault yourself by using the following guidelines. You will save yourself the costs of an unnecessary visit by customer service
personnel.
Faults that the customer can troubleshoot himself
Fault Cause Solution
Water flow-rate is too low The filter in either the water tap or the
showerhead is clogged.
Remove the filter and either clean it or
descale it.
A high water temperature is
set, but it is not reached.
The continuous-flow heater is connected
to a thermostatically-controlled water tap.
Set the temperature on the continuous-flow
heater to „60 °C“.
The display is blank. The fuse in the fusebox has tripped/blown. Check the fuse in the fusebox.
The water is not warm. The supply temperature has reduced. Reduce the water flow on the taps until the
desired water temperature is reached.
The temperature of the water
leaving the tap is higher than
the set temperature.
The temperature of the water supplying the
continuous-flow heater is higher than the
set temperature (e. g. due to pre-warmed
water supplied from a solar water heater).
The thermostatic premixer in the domes-
tic supply must be set accordingly to lower
temperatures.
“°C” flashes in the display. The power limit has been reached. Reduce the water flow at the tap or lower the
temperature setting on the appliance.
If the fault could not be eliminated, please call customer service.
Faults that the customer service specialist should troubleshoot
Fault Cause Solution
Water flow-rate is too low
despite cleaning of filter using
the water tap or showerhead
A filter in the appliance is clogged. Get a servicing expert to clean the appliance.
The display is blank despite
fault-free function of the
mains electricity supply fuses.
There is a fault in the appliance. Get a servicing expert to check the appliance.
The display shows the error
code “E..”.
There is a fault in the appliance. Get a servicing expert to check the appliance.
Faults that are automatically remedied
Fault Cause Solution
The display shows “00,0°C”. The air sensor in the appliance detects air
in the water and momentarily switches the
heating element off.
After a few seconds, the continuous-flow
heater automatically goes back into operation.
Guarantee
The guarantee conditions for this appliance are as defined by
our representative in the country in which it is sold.
Details regarding these conditions can be obtained from the
dealer from whom the appliance was purchased. The bill of
sale or receipt must be produced when making any claim
under the terms of this guarantee.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens DE2427527M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens DE2427527M in the language / languages: English, German, Dutch, French, Polish, Polish as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info