607939
33
Zoom out
Zoom in
Previous page
1/64
Next page
Trouble shooting en
33
3Trouble shooting
Trouble shooting
If a fault occurs, there is often a simple explanation.
Before calling the after-sales service, please refer to the
fault table and attempt to correct the fault yourself.
Note: If a dish does not turn out as well as you had
hoped, refer to the table section at the end of the
instruction manual, where you will find plenty of tips and
information. ~ "Tested for you in our cooking studio"
on page 37
:Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Fault table
If an error message beginning with 'E' is shown, e.g.
E0111, switch the appliance off and then on again. If
this message appears again, contact the after-sales
service.
Fault Possible cause Information/remedial action
The appliance does not work The fuse is faulty Check in the fuse box to make sure that the fuse for
the appliance is in working order
Power cut Check whether other kitchen appliances are working
The appliance door will not open; the
5 symbol is shown in the display
The appliance door is locked until the cooking com-
partment has cooled down.
Wait until the 5 symbol goes out
Although the appliance is switched
on, it cannot be operated; the 1
symbol is shown in the display
The child lock is activated
Press and hold the 1 button until the 1 symbol
goes out
E8010
The appliance door was opened immediately after the
button was pressed.
Close the appliance door and press the On/Off button
The interior lighting has failed The LED bulb is defective Call the after-sales service
Operations with steam or descaling
do not start or do not continue
Water tank empty Refill water tank
The panel is open Close the panel
Descaling locks operations with steam Carry out descaling
Faulty sensor Call the after-sales service
The appliance prompts you to rinse The power supply was interrupted or the appliance
was switched off during the descaling process
Once the appliance is switched on again, rinse it twice
The appliance prompts you to descale
without the counter appearing before-
hand
The set water hardness range is too low Carry out descaling
Check the set water hardness range and adjust it, if
necessary
Buttons flash Normal occurrence caused by condensation behind
the control panel
As soon as the condensation has evaporated, the but-
tons no longer flash
The cooking compartment does not
heat and "Demo mode on" is shown in
the display
The appliance is in demo mode Switch off the fuse in the fuse box and switch it back
on again after approx. 10 seconds. Switch on the
appliance and select "Demo mode off" in the settings.
The "Fill water tank" message
appears even though the water tank
is full
The panel is open Close the panel
The water tank is not clicked into place Click the water tank into place
~ "Steam" on page 20
Faulty sensor Call the after-sales service
The water tank has fallen off. Due to the impact, com-
ponents inside the water tank have come loose, and
the tank is leaking.
Order a new water tank
Panel does not open X
Power cut Check whether other kitchen appliances are working
The circuit breaker is faulty Check in the fuse box to make sure that the fuse for
the appliance is in working order
Faulty sensor Call the after-sales service
If required, empty the water tank: Open the appliance
door, take hold of the lower part of the panel on the
left and right with your fingers and pull out the panel
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens CN678G4S1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens CN678G4S1 in the language / languages: English as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens CN678G4S1

Siemens CN678G4S1 User Manual - German - 72 pages

Siemens CN678G4S1 User Manual - Dutch - 72 pages

Siemens CN678G4S1 User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info