71727
6
Zoom out
Zoom in
Previous page
1/22
Next page
en
6
Connecting the appliance
Have a technician install and connect the appliance
according to the enclosed installation instructions.
Do not remove the transportation protection devices
from the shelves and storage compartments until
the appliance has been installed.
Always connect the water before the power.
Apart from statutory national regulations, you should
stick to the connection terms relating to the local
electricity and water companies.
After installing the appliance, wait at least 1 hour until
the appliance starts up. During transportation the oil
in the compressor may have flowed into
the refrigeration system.
Before switching on the appliance for the first time,
clean the interior of the appliance (see chapter
“Cleaning the appliance”).
Water connection
The water may be connected only by a competent fitter
according to the local regulations of the appropriate
water supply company.
m Caution
Risk of appliance being damaged by particles!
The water filter must always be connected to the tap –
even if an additional filter system is used.
m Caution
Use only the enclosed hose set or a hose set
purchased from customer service for connection to the
drinking water mains.
The hose set must only be installed by customer
service.
Do not use existing or already used hose sets.
Connect the appliance to a drinking water line only:
ʋ Minimum pressure: 0.2 Mpa (2 bar)
ʋ Maximum pressure: 0.8 Mpa (8 bar)
ʋ Pressure over 0.8 MPa (8 bar): install a pressure
limiter between drinking water connection and hose
set
A separate shut-off valve should be installed
in the cold-water inflow.
The shut-off valve should not be located behind
the appliance. It is recommended that you mount
the shut-off valve directly next to the appliance or at
another place which is easily accessible.
When installing the water connection, pay attention
to the permissible installation area for the water mains.
For connection to the drinking water mains use only
water pipes which are suitable for drinking water.
Observe national regulations and the connection
conditions of the local water supply companies.
Note
The maximum outside diameter of the water mains
(without connecting pieces) is 10 mm.
Electrical connection
The socket must be near the appliance and also freely
accessible following installation of the appliance.
The appliance complies with the protection class I.
Connect the appliance to 220-240 V/50 Hz alternating
current via a correctly installed socket with protective
conductor. The socket must be fused with a 10
to 16 A fuse.
For appliances operated in non-European countries,
check whether the stated voltage and current type on
the rating plate match the values of your mains supply.
These specifications can be found on the rating plate
(see chapter “Customer service”).
m Warning
Never connect the appliance to electronic energy saver
plugs.
Our appliances can be used with mains and sine-
controlled inverters. Mains-controlled inverters are used
for photovoltaic systems which are connected directly
to the national grid. Sine-controlled inverters must be
used for isolated applications (e.g. on ships or in
mountain lodges) which are not connected directly to
the national grid.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens CI 30 RP 00 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens CI 30 RP 00 in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Siemens CI 30 RP 00

Siemens CI 30 RP 00 User Manual - German - 22 pages

Siemens CI 30 RP 00 User Manual - Dutch - 40 pages

Siemens CI 30 RP 00 User Manual - French - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info