296325
4
Zoom out
Zoom in
Previous page
1/16
Next page
4
© Siemens AG 2004, C:\Daten_itl\Siemens\DTP-Satz\Produkte\AX72_Pegasus_DTC\out-
left page (4) of AX72 Pegasus-DTC, SUG, en, A31008-H2860-A1-2-7619 (04.10.2005, 10:58)
VAR Language: en; VAR issue date: 050307
When charging is in progress h is
displayed.
Charging time
An empty battery is fully charged after
about 2 hours. Charging is only possible
within a temperature range of
+5 °C to +40 °C. If the temperature ris-
es/falls 5 °C above/below this, the charge
symbol flashes a warning. The mains volt-
age specified on the power supply unit
must not be exceeded (Operating time,
p. 12).
Only use the power supply unit provided!
Display while in service
Charge level display during operation
(empty - full):
adg.
A beep sounds when the battery is nearly
empty. The charge level of the battery is
only displayed correctly after an uninter-
rupted charging/discharging cycle. You
should therefore not remove the battery
unnecessarily and where possible not
terminate the charging process early.
Security
§Menu§ ¢ m ¢ Security
¢ Select function.
The phone and SIM card are protected
against misuse by several security codes.
Keep these confidential numbers in a safe
place where you can access them again if
required.
Codes
PIN control
You can stop the PIN prompt being
activated when the phone is switched on,
but you then risk unauthorised use of the
phone.
Press
§Change§
. Enter PIN and confirm
with
§OK§.
Change PIN
You can change the PIN to any 4- to 8-digit
number you find easier to remember.
Change PIN2
(Display only if PIN2 is available). Proceed
as with Change PIN.
Change phonecode
You define the phone code (4-8 digits)
when you call up a protected function for
the first time. It is then valid for all phone-
code protected functions.
Clear SIM card barring
If the PIN is entered incorrectly three
times, the SIM card is barred. Enter the
PUK (MASTER PIN), provided by your serv-
ice provider with the SIM card, according
to instructions. If the PUK (MASTER PIN)
has been lost, please contact your service
provider.
Preventing accidental activation
Even if PIN control is deactivated confirma-
tion is required to switch on the phone.
This prevents the phone from being
switched on accidentally, e. g. when car-
ried in a pocket or whilst you are on an
aircraft.
Press and hold the On/Off/End key
B
and confirm with §OK§. The phone switch-
es on.
Calling
Dialling with number keys
The phone must be switched on (standby
mode). Dial number (always with area
code, if necessary with international dial-
ling code). To dial international dialling
code press and hold
0 until a "+" is dis-
played. Press
§Country§ and select country.
Short press
§Clear§ to clear the last digit, a
long press clears the entire phone
number. To dial press the Call key
A.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siemens ax72 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siemens ax72 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info