668266
10
Zoom out
Zoom in
Previous page
1/22
Next page
4
English
5 Hook the front of the housing
onto the base plate at the top and
close. Tighten the screw on the
underneath of the housing.
Mounting TR603-…
6 Mount the transformer on the top
hat rail (distribution).
7 Surface mounting is possible with
accessory ZAP3-0. (not included in
scope of supply)
Mounting HTS811-…
Strip back cable to appr. 80mm.
8 Open the device from the back by
pressing in the locking lever.
9 Recommended mounting height
appr. 1.50m /4.9ft. to centre
device.
10 When mounting directly on the
wall, fasten the base plate using 4
screws, paying attention that the
plate is the right way up
(top marking).
11 When mounting on a switch box,
use the screw openings in the centre
of the device, paying attention that
the plate is the right way up
(top marking).
12 Install in accordance with the
terminal diagram. The cores of the
installation cable must be stored
inside the free installation space in
the base plate.
13 Insert the coloured plug of the
spiral cable into the socket at the
housing. A distinct click is audible
when the plug is correctly inserted.
14 Insert the other end of the spiral
cable in the receiver until the plug
clicks audibly into place. This con-
nection can no longer be detached.
15 Hook the housing into the base
plate from above and close by
exerting a slight pressure.
Dismantling
16 To remove the housing, press
the lock upwards using a at blade
screwdriver. The circuit board and
receiver remain on the upper part of
the housing.
Application
The Siedle Compact audio set for
1–4 residential units. Encompasses
the door station for surface
mounting, transformer for dis-
tributor mounting and in-house
telephones for surface mounting.
With the basic functions calling,
speech and door release. Illuminated
information panel.
Electrical voltage
Mounting, installation and ser-
vicing work on electrical devices may
only be performed by a suitably
qualied electrician.
Failure to observe this regulation
could result in the risk of serious
damage to health or fatal injury due
to electric shocks.
Observe DIN EN 60065! In a
building installation, an all-pole
mains switch with a contact opening
of at least 3 mm must be provided.
The transformer must not be
exposed to water drops or sprayed
water! Ensure sufcient ventilation,
paying particular attention to ensure
that ventilation slots are not covered.
For surface mounting, ensure that
“protection against direct contact”
with active parts is provided. For
details, consult VDE 0100/DIN 57100
part 410.
When using stranded cores as
cable material, these must be tted
with wire end ferrules without fail.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of supply SETCA812-1
CA 812-1
HTS 811-…
TR 603-…
Siedle screwdriver
This product information
Scope of supply SETCA812-2
CA 812-2
2 x HTS 811-…
TR 603-…
Siedle screwdriver
This product information
Scope of supply SETCA812-3
CA 812-4
3 x HTS 811-…
TR 603-…
Siedle screwdriver
This product information
Scope of supply SETCA812-4
CA 812-4
4 x HTS 811-…
TR 603-…
Siedle screwdriver
This product information
Mounting CA812-…
1 Unscrew the front of the housing.
To do this, release the Siedle screw
on the underneath of the housing.
Hinge the front of the housing
forward.
2 Surface mounting the door sta-
tion. Recommended mounting
height appr. 1.50m /4.9ft. to centre
device. Please note: The cable is
inserted in the lower area of the
base plate!
3 Strip back the installation cable
close to the wall (appr. 10 mm)
and insert the cores into the base
plate. Fasten the base plate using 4
screws. Close the two openings at
the top using rubber stoppers. Install
in accordance with the terminal
diagram.
The cores may only be laid in the
admissible installation space.
4 Depending on the installation
environment, it may be necessary
to change the door station speech
volume in order to permit clear
speech transmission.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siedle SET CA 812-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siedle SET CA 812-4 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 3,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info