668265
11
Zoom out
Zoom in
Previous page
1/22
Next page
5
Installation
17 Connect in accordance with the
terminal diagram.
18 Wiring diagram with CTÖ 602-0.
19 For each call button, a maximum
of two in-house telephones can be
connected. Connection of a storey
call button (ERT) is only possible
with the storey call button accessory
ZERT811-…
Terminal assignment CA812-…
1, 7… System line 1+n
b, c Power supply 12VAC
Relay contact door release
Li Relay contact light
D+, D- CTÖ602-…/SFC602-…
control
Terminal assignment TR 603-…
b, c Power supply 12VAC
L1, N Power connection
Terminal assignment HTS811-…
1, 7 System line 1+n
ERT Storey call button
Range
Range from the transformer to the
door station max. 50m, transformer
to the in-house telephone 400m
with 0.8mm conductor material.
When operating 2 in-house tele-
phones in parallel, the range reduces
to 200m.
*) Using the light button in the in-
house telephones HTS811-… the
light contact in the door loudspeaker
is closed for 0.8 seconds. The refer-
ence for this contact is terminal c,
pick-off at terminal Li. Following
completion of the installation, this
function is active without any further
programming. To actuate the stair-
case and/or outside light, according
to VDE regulations a light current
relay or time relay (e.g. ZR502-…)
must be interconnected. Contact
load max. 15VAC, 30VDC,
switching time 0.8 seconds.
In parallel to an in-house telephone,
the secondary signal controller
NSC602-… can be connected, e.g.
for actuation of a radio chime. The
NS711-… can be operated as an
additional signalling unit in parallel
at an HTS811-…
It is not possible to connect other
devices such as a DCA612-… or
HTC811-…
Lettering
20 Open the nameplate from the
outside, for example using a at
bladed screwdriver, and carefully
remove the inscription insert. To
insert the nameplate, lock into place
by exerting light pressure.
21 Info sign from the inside, e.g.
open using at blade screwdriver
and remove inscription eld. To
insert, clip in the info sign exerting a
slight pressure.
Troubleshooting
The transformer is tted with a
thermal fuse on the primary side.
After short circuit or overload
• Disconnect the device from the
power supply for appr. 1 min.
• Remedy the fault.
• Restore the mains power.
Specications CA812-…
Contact type: n.o. contact 24V, 2A
Protection system: IP54
Ambient temperature:
–20°Cto+55°C
Dimensions (mm) WxHxD:
82x226x33
Specications TR603-…
Operating voltage: 230VAC,
+/-10%, 50/60Hz
Output voltage: 12VAC
Output current: max.1.3A
Fusing:
Secondary side with thermal fuse
Protection system: IP30
Ambient temperature:
0°Cto+40°C
Horizontal pitch (HP): 3
Dimensions (mm) WxHxD:
53.5x89x60
Specications HTS811-…
Dimensions (mm) WxHxD:
91x201x46
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Siedle SET CA 812-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Siedle SET CA 812-3 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 3,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info