139803
42
Zoom out
Zoom in
Previous page
1/43
Next page
41
Troubleshooting Guide
If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation,
consult your dealer. Under no circumstances should you repair the unit yourself as this will invalidate the
guarantee!
ENGLISH
PROBLEM POSSIBLE CAUSE REMEDY
No power
No playback
Malfunction
No picture
Noisy or distorted
picture
Abnormal picture or
no picture
Slight pause of
picture
No sound
Noisy or distorted
sound
Remote control unit
does not operate.
• The AC input cord is disconnected.
• Poor connection at AC wall outlet or the outlet
is inactive.
• The disc is loaded upside down.
• The disc is not playable.
• The disc is dirty.
• The rating level is not set correctly.
The symbol about invalid operation is displayed.
• The disc is scratched or dirty badly.
• The video cords are disconnected.
• The incorrect selection of input source on the
TV.
• The disc is not playable.
• The unit is connected to a VCR directly and the
copyguard function is activated.
• The disc is dirty.
• It is in rapid advance or reverse playback, or in
frame advance or reverse playback.
• The video output signal is not selected
correctly.
• The layer transition occurs during playback of
DVD Videos recoded in dual-layer format.
• The audio cords are disconnected.
• The speakers are disconnected to the amplifier.
• The incorrect selection of input source on the
amplifier.
• The AUDIO OUT is not set correctly.
• The disc is dirty.
• Poor connections.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
Connect cord securely.
Check the outlet using a lamp or another
appliance.
Reload the disc with the printed side up.
Use a playable disc.
Clean the disc.
Set the rating level setting correctly.
(Refer to "When selecting the RATING LEVEL"
on page 32.)
Adjust the setting correctly.
(Refer to "SYMBOL ABOUT INVALID
OPERATION" on page 12.)
• Press the POWER ON/OFF switch to switch the
power off, press the POWER ON/OFF switch
again and then unload the disc.
Connect the cords correctly.
Select the input source correctly.
Use a playable disc.
Connect the unit so that the picture signal is
transferred directly to the TV.
Clean the disc.
Sometimes a small amount of picture distortion
may appear. This is not malfunction.
• Select the video output signal correctly.
(Refer to "SELECTING THE VIDEO OUTPUT
SIGNAL" on page 27.)
• Sometimes slight pause may occur.
This is not malfunction.
Connect the cords correctly.
Connect the speakers correctly.
Select the input source correctly.
Set the AUDIO OUT correctly.
(Refer to "SETTING THE AUDIO SETUP" on
page 35.)
Clean the disc.
Check the connections and connect all cords
securely.
Replace the batteries.
Remove the obstacle.
V-903V(G) 2006.4.20 05:58 PM 페이지 41
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sherwood v 903 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sherwood v 903 in the language / languages: English as an attachment in your email.

The manual is 1,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sherwood v 903

Sherwood v 903 User Manual - German - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info