459227

Sherwood R-904N NetBoxx Manual

52
Zoom out
Zoom in
Previous page
1/63
Next page
ENGLISH
52
• Then “X.OVER ~” will be displayed.
• Then “T.TONE ~” will be displayed.
When selecting the CROSSOVER FREQUENCY
1. Press the CURSOR UP/DOWN buttons to select the “X.OVER”, then press the ENTER button.
2. Press the CURSOR LEFT/RIGHT buttons to set the crossover frequency as desired.
• You can select the crossover frequency among 50, 80, 100, 150 and 200 Hz.
■About the crossover frequency
• When speakers are set to “SMALL”, low frequencies in those channels that are below the crossover frequency are to output
from subwoofer or front speakers which are set to “LARGE” (when not using a subwoofer).
• Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100Hz ~ 20kHz,
the crossover frequency should be set to 100 Hz (or slightly higher).
When selecting the CHANNEL LEVEL
• Each time these buttons are pressed, the mode changes as follows :
M (MANUAL) : To move the test tone manually from speaker to speaker and to adjust the individual channel levels.
↕
A (AUTO) : To adjust the channel levels as the test tone moves from speaker to speaker automatically.
1. Press the CURSOR UP/DOWN buttons to select the “CH LEVEL”, then press the ENTER button.
2. Press the CURSOR LEFT/RIGHT buttons to select the desired mode.
3. Press the ENTER button to confirm your selection.
• After the volume increases to the reference level, test tone will be output.
• When the “A” (AUTO) is selected, the test tone will be output from each speaker for 2 seconds.
• When the “M” (MANUAL) is selected, select the speakers to be output the test tone with using the CURSOR UP/DOWN
buttons.
• You can adjust the channel level within the range of -15 ~ +15 dB.
■Note :
• The test tone will not be output from the speakers set to “NO”.
4. Press the CURSOR LEFT/RIGHT buttons to adjust the level of each channel.
• The previous menu will be returned.
5. To cancel the test tone function, press the RETURN button.
R-904N(A)_ENG_091007:R-904N(A) 2009-10-14 오후 1:53 페이지 52
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sherwood R-904N NetBoxx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sherwood R-904N NetBoxx in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info