459227

Sherwood R-904N NetBoxx Manual

18
Zoom out
Zoom in
Previous page
1/63
Next page
ENGLISH
18
Programming a macro function
• The macro function enables you to program a
series of button operations(up to 10) on this
remote control into a single button.
• You can store up to three separate macro
command sequences into “M1”, “M2” and “M3”
buttons.
• If the macro mode is entered, the LED will flicker
once.
Example: When programming a series of button
operations into “M1” button.
1. Press and hold down both “ENTER” button and
one of three NUMERIC buttons (“1” ~ “3”)
corresponding to “M1”~”M3” buttons for more
than 1 second.
■Note :
You should press the corresponding DEVICE
buttons before pressing each operation button.
Example: When playing a BD on the BD player
connected to VIDEO 2 jacks of this
receiver.
①. Press “AVR” button to control this receiver.
②. Press “POWER ON” button to turn this
receiver on.
③. Press “AVR” button to control this receiver.
④. Press “VIDEO 2(7)” button to select the
desired input source.
⑤. Press “BD” button to control the BD player.
⑥. Press “POWER ON” button to turn the BD
player on.
⑦. Press “BD” button to control the BD player.
⑧. Press “▶” button to start playback.
2. Press the operation buttons you want to
program in order.
3. Press “ENTER” button.
• If the programming is performed successfully, the
LED will flicker twice.
■To remove a macro program
• When removing a macro program, perform the
above steps 1 and 3, but ignore the step 2.
■To change a macro program
• When a new macro program is stored into a
MACRO button with performing the above steps
1 to 3, the previous macro program is cleared
from the memory of the MACRO button.
Operating a macro function
■Notes:
• The codes programmed into a MACRO button will be
transmitted at an interval of 0.5 seconds. However,
some components may not be able to complete one
operation in 0.5 seconds and may miss the next code.
In this case, the macro function cannot control the
corresponding components correctly.
• Be sure to use the remote control within the remote
control operation range of the components.
• Depending on the operation status of the components,
etc., the macro function cannot control the
corresponding components correctly.
• Aim the remote control at the REMOTE SENSORs of
the components to be controlled and press the MACRO
button you want.
Example: When pressing “M1” button.
R-904N(A)_ENG_091007:R-904N(A) 2009-10-14 오후 1:53 페이지 18
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sherwood R-904N NetBoxx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sherwood R-904N NetBoxx in the language / languages: English as an attachment in your email.

The manual is 3,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info