489151
42
Zoom out
Zoom in
Previous page
1/51
Next page
ENGLISH
42
Troubleshooting Guide
If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your
dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the warranty.
PROBLEM POSSIBLE CAUSE REMEDY
No power
N
o sound
No sound from the surround
s
peakers
No sound from the center
speaker
No sound from the surround back
speakers
No picture
No picture with an HDMI
connection
Noise or distorted picture
Stations cannot be received
Preset stations cannot be
received
Poor FM reception
Remote control unit does not
operate.
The AC input cord is disconnected.
• Poor connection at AC wall outlet or the outlet is
dead or off.
• The speaker wires are disconnected.
The master volume is adjusted too low.
The MUTE button is pressed to ON.
• Incorrect selection of input source.
• Incorrect connections between the components.
• The HDMI Audio Out is set to THRU.
Surround mode is switched off(stereo mode).
Master volume and surround level are too low.
Monaural source is used.
• Surround speaker setting is “NO”.
• Stereo mode, etc is selected.
• Center speaker setting is “NO”.
• Master volume and center level are too low.
• The input signal format or the current surround
mode cannot support the 7.1(or 6.1) surround.
• The surround back channels' power amplifier is
assigned to “R2”.
Master volume and surround back level are too low.
• Surround back speaker setting is “NO”.
• Video connections between this unit and the
monitor TV are not made correctly.
• Incorrect selection of input source on the monitor
TV.
• HDMI connection between this unit and the
monitor TV is not made correctly.
• The monitor TV or other equipments do not
support HDCP.
• Video format of your monitor TV, BD/DVD player,
etc. is different from PAL.
• No antenna is connected.
• The desired station frequency is not tuned in.
• Antenna is in wrong position.
An incorrect station frequency has been memorized.
• The memorized stations are cleared.
• No antenna is connected.
The antenna is not positioned for the best reception.
• Weak signals.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
Connect cord securely.
Check the outlet using a lamp or another
appliance.
• Check the speaker connections.
• Adjust the master volume.
Press the MUTE button to cancel the muting effect.
Select the desired input source correctly.
Make connections correctly.
• Set it to AMP. (For details, refer to “When
selecting the HDMI (HDMI Audio Out)” on page
24.)
• Select a surround mode.
Adjust master volume and surround level.
Select a stereo or surround source.
• Select the desired surround speaker setting.
• Select the desired surround mode.
• Select the desired center speaker setting.
• Adjust master volume and center level.
• Under the proper situations, perform the 7.1(or
6.1) surround playback.(For details, refer to
“ENJOYING SURROUND SOUND” on page 22.)
• Assign the power amplifier to the surround back
channels.(For details, refer to “When selecting
the AMP ASSIGN” on page 35.)
• Adjust master volume and surround back level.
• Select the desired surround back speaker setting.
• Make proper video connections.
• Select the input source correctly.
• Make proper HDMI connection.
• This unit will not output video signal unless the
connected equipments supports HDCP.
• Change the video format to PAL.
• Connect an antenna.
• Tune in the desired station frequency.
• Move antenna and retry tuning.
• Memorize the correct station frequency.
• Memorize the stations again.
• Connect an antenna.
• Change the position of the antenna.
• Install an outdoor FM antenna.
• Replace the batteries.
• Remove the obstacle.
R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 42
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sherwood R-904 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sherwood R-904 in the language / languages: English as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sherwood R-904

Sherwood R-904 User Manual - German - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info