489151

Sherwood R-904 Manual

36
Zoom out
Zoom in
Previous page
1/51
Next page
ENGLISH
36
SETTING THE ROOM EQ
• Room EQ lets you avoid troublesome listening-based speaker setup and achieve good surround sound. Room EQ has the
feature that provides the optimum listening environment at the listening position in your room. You should connect the
supplied microphone to the SETUP MIC jack so that this receiver can analyze the information form a series of test tones
emitted from speakers at listening position and can adjust the size, channel level, distance and frequency response of each
speaker automatically.
• If you want to personalize your speaker setup by making the settings manually, perform the “SETTING THE SPEAKER
SETUP” on page 37.
• After the Room EQ setup has been completed, set the Room EQ as desired. (For details, refer to “When selecting the “EQ
(Room EQ)” on page 23.)
■Preparations
①. Check that the speakers are securely connected to this receiver.
• If your subwoofer has adjustable volume and crossover frequency, set the volume halfway and set the crossover frequency
to the maximum or the low pass filter off.
②. Connect the supplied microphone to the SETUP MIC jack on the front panel.(For details, refer to “SETUP MIC JACK” on
page 11.)
■Notes :
• Because the microphone for Room EQ setup is designed for use with this receiver, to use the Room EQ setup function, do not
use a microphone other than the one supplied with this receiver.
• After you have completed the Room EQ setup procedure, disconnect the microphone.
• If possible, use a tripod, etc. to attach the microphone at the same height as your ears would be when you are seated in your
listening position.
• Ensure there are no obstacles between the speakers and the microphone.
1. Place the microphone on a flat level surface at the listening position.
2. Press the ENTER button to check the speaker configuration when “SET RMEQ” is displayed.
• “SET RMEQ” flickers while the receiver outputs the test tones to determine the speakers present in your setup and then
“CHECK OK” is displayed.
■Notes :
• Try to be as quiet as possible while outputting the test tones.
• For correct speaker settings, do not adjust the volume while outputting the test tones.
• If there is too much ambient noise, error message will be displayed.
In such a case, press the ENTER button to confirm “RETRY?” after checking for ambient noise.
• If there may be a problem with speaker connection, “ERR ~” (error message) will be displayed.
If confirming “RETRY?” with pressing the ENTER button does not fix the problem, turn off the power and check the speaker
connection.
• Each time the CURSOR UP/DOWN buttons are pressed, the speaker is changed.
• If the speaker configuration is not correct, press the CURSOR LEFT/RIGHT buttons to change the setting. When the
correction is finished, confirm the speaker configuration.
• Then the Room EQ setup will start.
• If any operation is not performed while displaying “CHECK OK” for 10 seconds, the Room EQ setup will start automatically.
3. To check the speaker configuration, press the CURSOR UP/DOWN buttons to select the speaker.
4. To confirm the speaker configuration, press the CURSOR UP/DOWN buttons to select “CHECK OK”, then
press the ENTER button.
• Then the settings made in the Room EQ setup are memorized. You can check these settings on the “SPEAKER SETUP”
menu. (For details, refer to “SETTING THE SPEAKER SETUP” on page 37.)
5. If the Room EQ setup has been completed, it will be returned to the Room EQ setup.
R-904(G)_ENG_091014:R-904(G) 2009-11-11 오후 12:05 페이지 36
… 36 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sherwood R-904 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sherwood R-904 in the language / languages: English as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sherwood R-904

Sherwood R-904 User Manual - German - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info