457672
29
Zoom out
Zoom in
Previous page
1/71
Next page
25
Basisbediening
In/uitschakelen van de projector
Betreffende de lampindicator
De lampindicator geeft de status van de lamp aan.
Groen: De lamp is aan.
Knippert groen:
De lamp is aan het opwarmen.
Rood: De lamp wordt op een abnormale
wijze uitgeschakeld of de lamp moet
vervangen worden.
•Wanneer de projector wordt ingeschakeld, kan het
beeld enigszins flikkeren gedurende de eerste minuut
dat de lamp is ingeschakeld. Dit is normaal en wordt
veroorzaakt door de regelcircuits van de lamp die de
uitgangskarakteristieken van de lamp stabiliseren. Dit
verschijnsel duidt niet op een defect.
Als de projector in de ruststand (standby) wordt
gezet en dan meteen weer wordt ingeschakeld,
kan het even duren voordat de lamp gereed is
om te beginnen met projecteren.
Wanneer de systeemvergrendeling is ingesteld, verschijnt
een invoervakje voor de toegangscode. Om de
toegangscode-instelling te annuleren, voert u de
toegangscode in die u reeds hebt ingesteld. Zie blz. 44
voor nadere bijzonderheden.
Beeldschermdisplay (bevestigingsmelding)
STANDBY/ON toets
De projector uitschakelen (de
projector in de ruststand zetten)
Druk op STANDBY/ON van de projector
of op STANDBY van de
afstandsbediening en druk dan nog een
keer op die toets terwijl de
bevestigingsmelding wordt aangegeven
om de projector in de ruststand
(standby) te schakelen.
• De projector kan niet aangezet worden tijdens
het koelen.
Direct Uit functie:
U kunt de stekker uit het stopcontact halen
ook als de koelventilator nog draait.
Opmerking
Info
Wanneer “Automatisch herstarten” op
“Aan” staat:
Als het netsnoer niet in het stopcontact zit of de
schakelaar staat uit wanneer de projector aan staat,
dan gaat de projector automatisch aan wanneer u
het netsnoer in het stopcontact steekt of wanneer
de schakelaar aanstaat. (Zie blz. 43.)
Bij het verlaten van de fabriek is de taal op
Engels ingesteld. Als u een andere taal voor het
beeldschermdisplay wilt instellen, moet u de taal
wijzigen zoals beschreven op blz. 42.
Info
STANDBY
toets
De projector inschakelen
Voordat u de onderstaande aanwijzingen
uitvoert, moet u eerst alle externe
apparatuur aansluiten en de stekker in het
stopcontact steken. (Zie blz. 21 tot 24.)
Spanningsindicator
ON toets
Verwijder de lensdop en druk op
STANDBY/ON van de projector of ON
van de afstandsbediening.
De spanningsindicator licht groen op.
Na het oplichten van de lampindicator is de projector
klaar voor bediening.
Lampindicator
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp XR-30X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp XR-30X in the language / languages: Dutch as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info