469889
56
Zoom out
Zoom in
Previous page
1/92
Next page
52
0
0
0
0
Phase
Clock
H-Pos
V-Pos
Reset
Auto
1024 x 768
Ein
Standard
Auto
WÄ./EINS.
Zurück
OK
AUS
Auflösung
Auto-Sync.
Signaltyp
Dynam. Bereich
Videosystem
0 IRE
Videoeinr.
Signal-Info : 1024 x 768
H 48.3 kHz / V 60.0 Hz
Bild Audio SIG BIW Option Netz
1
Einstellung des Computerbildes
Wenn das optimale Bild nicht mit der Auto-Sync-
Anpassung erhalten werden kann, verwenden
Sie die SIG-funktion.
Vergbare
Elemente
Beschreibung
Clock
Zum Einstellen von vertikalen Störungen
Phase
Zum Einstellen von horizontalen Störungen
(wie Spurabgleich bei Ihrem Videorecorder)
H-Pos Zum Zentrieren der Bildschirmanzeige
durch Bewegen nach links oder rechts
V-Pos Zum Zentrieren der Bildschirmanzeige
durch Bewegen nach oben oder unten
Um alle Anpassungselemente zurückzusetzen,
wählen Sie „Reset, und betätigen Sie ENTER.
Der verstellbare Bereich für „H-Pos“ und „V-Pos“
kann je nach Bildschirmaufl ösung abweichen.
Hinweis
2
Aufl ösung-Einstellung
Normalerweise wird die Art des Eingangssignals
erkannt und die dafür geeignete Aufl ösungs-
Betriebsart automatisch eingestellt. Bei einigen
Signalen sollte die optimale Aufl ösungs-Betriebsart
in „Aufl ösung“ gewählt werden, um der Anzeige-
Betriebsart des Computers zu entsprechen.
Siehe „Prüfung des Eingangssignals“ auf Seite
53r Information über das aktuell gewählte
Eingangssignal.
Hinweis
3
Auto-Sync.-Einstellung
Für die automatische Einstellung eines
Computerbildes.
Vergbare
Elemente
Beschreibung
Ein Die Auto-Sync.-Einstellung wird beim
Einschalten des Projektors oder bei
der Umschaltung der Eingangssignale
beim Anschluss an einen Computer
durchgeführt.
Aus Die Auto-Sync.-Einstellung wird nicht
automatisch ausgeführt.
Auto-Sync-Anpassung wird auch durch Dcken
von AUTO SYNC am Projektor oder an der
Fernbedienung ausgeführt.
Die Auto-Sync.-Einstellung könnte abhängig
vom Bild des an den Projektor angeschlossenen
Computers einige Zeit benötigen.
Hinweis
4
Einstellung des Signaltyps
Diese Funktion erglicht Ihnen die Auswahl
des Eingangssignaltyps RGB oder Komponente
für COMPUTER/COMPONENT 1, 2.
Vergbare
Elemente
Beschreibung
Auto Eingangssignale werden automatisch
als RGB- oder Komponentensignale
erkannt.
RGB Einstellen, wenn RGB-Signale empfangen
werden.
YPbPr Einstellen, wenn Komponentensignale
empfangen werden.
Signalanpassung („SIG-Menü)
Menübetrieb n Seite 46
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp XG-SV200X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp XG-SV200X in the language / languages: German as an attachment in your email.

The manual is 13,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp XG-SV200X

Sharp XG-SV200X User Manual - English - 92 pages

Sharp XG-SV200X Quick start guide - Dutch - 26 pages

Sharp XG-SV200X User Manual - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info