469885
50
Zoom out
Zoom in
Previous page
1/59
Next page
-50
Video Wall Projection
Projector 1:
Master
Projector 2:
Slave
Projector 3:
Slave
Projector 4:
Slave
LAN terminal
LAN terminal
LAN terminal
LAN terminal
LAN cable
LAN cable
(straight-through type)
Hub
Computer
1 Change the TCP/IP settings for the
computer as shown below.
(See “Setting an IP Address for the Computer”
on page 22 for the details.)
IP address : 192.168.150.2
Subnet mask : 255.255.255.0
Default gateway :
(Do not input any values.)
2 Change the TCP/IP settings for
each projector as shown below.
(See “Setting up a Network Connection for the
Projector” on page 24 for the details.)
IP address Projector 1 : 192.168.150.3
Projector 2 : 192.168.150.4
Projector 3 : 192.168.150.5
Projector 4 : 192.168.150.6
Subnet mask : 255.255.255.0
Default gateway : 0.0.0.0
Note
The TCP/IP settings shown are examples
to make connections following the diagram.
When using other equipment in the same
network, be careful about the IP address
overlap or other network settings.
Consult your network administrator for as-
sistance with the network settings.
3 Connect the computer and the pro-
jectors as shown below.
Preparation
Follow the procedure below after setting up the basic connection.
When “User Name” and “Password” have been set to the projector, reset them before the stack projec-
tion setup. To set “User Name” and “Password”, use the same user name and password for both of the
master and slave projectors. (See page 28.)
Set “Data Port” with the same number for both of the master and slave projectors. (See page 29.)
Info
Do not use network software or equipment while it is accessing the projector via the port of the same
number used for the master or slave projector, otherwise you cannot properly control multiple projectors
with one remote control.
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp XG-P610X-N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp XG-P610X-N in the language / languages: English as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp XG-P610X-N

Sharp XG-P610X-N User Manual - English - 86 pages

Sharp XG-P610X-N User Manual - Dutch - 86 pages

Sharp XG-P610X-N User Manual - Dutch - 59 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info