216214
69
Zoom out
Zoom in
Previous page
1/74
Next page
65
Appendix
Problem
An unusual sound is
occasionally heard from
the cabinet.
Maintenance indicator on
the projector illuminates
or blinks in red.
The projector cannot
be turned on or put into
the standby mode
using STANDBY/ON on
the projector.
Picture is green on
COMPUTER
(Component)/
DVI (Component).
Picture is pink
(no green) on
COMPUTER (RGB)/
DVI (RGB).
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.
The remote control
cannot be used.
Check
If the picture is normal, the sound is due to cabinet shrinkage caused
by room temperature changes. This will not affect operation or
performance.
See “Maintenance Indicators”.
The keylock is set.
If the keylock is set to “ON”, all the buttons are locked.
Change the input signal type setting.
When you cannot select an input signal type, select “Color is faded
or poor” in the “Help” menu, after selecting an item other than
“sRGB” in “Picture Mode”, and then select an input signal type.
Image adjustments are incorrectly set.
When temperature inside the projector increases, the cooling fan
runs faster.
The lamp indicator is illuminating in red.
Replace the lamp.
Cables are incorrectly connected to the projector or the connected
equipment works improperly.
Select “Vertical stripes or flickering image appear” in the “Help”
menu and make the necessary adjustments.
If this happens frequently, replace the lamp.
The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
Operate the remote control while pointing it at the projector’s remote
control sensor.
The remote control may be too far away from the projector.
If direct sunlight or a strong fluorescent lamp is shining on the
projector’s remote control sensor, place the projector where it will not
be affected by strong light.
The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
Page
50
47
48
40, 48
41
8, 9
49, 50, 51
50, 53
21–24
48
53
53
15
14
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp xg f262x at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp xg f262x in the language / languages: English as an attachment in your email.

The manual is 2,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info