469870
67
Zoom out
Zoom in
Previous page
1/71
Next page
-65
Appendix
CheckProblem Page
Maintenance
indicator illuminates or
blinks in red.
The projector cannot be
turned on or put into the
standby mode using the
STANDBY/ON button on
the projector.
Picture is green with
component input signals
(COMPUTER/
COMPONENT 1, 2, DVI-D)
.
Picture is pink (no green)
with RGB input signals
(COMPUTER/
COMPONENT 1, 2, DVI-D)
.
Picture is too bright and
whitish.
The black levels of the
image show banding or
appear faded when DVI-
D is selected.
The cooling fan
becomes noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp takes a long
time to turn on.
Picture is dark.
The remote control
cannot be used.
See “Maintenance Indicators”.
The keylock is set.
If the keylock is set to ON, all the buttons are locked.
Change the input signal type setting.
Image adjustments are incorrectly set.
Select the Dynamic Range setting (“Standard” or “Enhanced”)
that results in the best picture quality.
When temperature inside the projector increases, the cooling
fan runs faster.
The lamp indicator is illuminating in red.
Replace the lamp.
Cables incorrectly connected to the projector or the connected
equipment works improperly.
If this happens frequently, replace the lamp.
The lamp will eventually need to be changed.
The lamp has reached the end of its life. Replace the lamp.
Operate the remote control while pointing it at the projector’s
remote control sensor.
The remote control may be too far away from the projector.
If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it
will not be affected by strong light.
The batteries may be depleted or inserted incorrectly. Make
sure the batteries are inserted correctly or insert new ones.
58
50
45
44
45
58
23-29
60
60
15
15
This projector is equipped with a microprocessor. Its performance could be adversely affected by
incorrect operation or interference. If this should happen, unplug the projector and plug it in again
after more than 5 minutes.
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp XG-C465X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp XG-C465X in the language / languages: English as an attachment in your email.

The manual is 6,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp XG-C465X

Sharp XG-C465X Quick start guide - English - 45 pages

Sharp XG-C465X User Manual - German - 71 pages

Sharp XG-C465X User Manual - German - 45 pages

Sharp XG-C465X Quick start guide - Dutch - 45 pages

Sharp XG-C465X User Manual - Dutch - 71 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info