526653
3
Zoom out
Zoom in
Previous page
1/4
Next page
Maintenance
Batteries
This register displays a low battery warning
message “LOW BATTERY” when the batteries are
low, and displays a no battery warning message
“NO BATTERY” when batteries are extremely low
or batteries are not installed.
If no batteries are installed, install two new alkaline
batteries LR6 (“AA” size) at once. If batteries
are already installed, replace them with new
ones as soon as possible. If the AC power cord
is disconnected or a power failure occurs when
the batteries are dead or not installed, all the
programmed settings will be reset to the default
settings and any data stored in memory will be
cleared.
C
Improper use of batteries could cause them
to burst or leak, which might damage the
interior of the register. Please take the
following precautions:
Be sure that the positive (+) and negative
(-) poles of each battery are oriented
properly.
Never mix batteries of different types.
Never mix old batteries and new ones.
Never leave dead batteries in the battery
compartment.
Remove the batteries if you plan not to
use the register for long periods.
Should a battery leak, clean out the
battery compartment immediately, taking
care not to let the battery uid come into
direct contact with your skin.
If an incorrect battery is used, it may
explode or leak.
For battery disposal, follow the relevant
law or regulation in your country.
Replacement
1. Be sure the register is plugged in.
2. Remove the printer cover.
3. Open the battery cover and remove the old
batteries.
Reading and Resetting Sales
List of All Available Report
Use the reading function (X) when you need to
take the reading of sales information entered after
the last resetting. You can take this reading any
number of times. It does not affect the register’s
memory.
Use the resetting function (Z) when you need to
clear the register’s memory. Resetting prints all
sales information and clears the entire memory
except for the GT1 through GT3, reset count, and
consecutive number.
X1 and Z1 reports show daily sales information.
You can take these reports in the X1/Z1 mode.
X2 and Z2 reports show periodic (monthly)
consolidation information. You can take these
reports in the X2/Z2 mode.
In the OP X/Z mode, an clerk can take his or her
report.
If you want to stop the printing report, press the
a
key.
Item
Mode
OP X/Z X1/Z1 X2/Z2
X Z X Z X Z
General report
Department by group
report
Individual department
group report
Department group total
report
Transaction report
Total-in-drawer report
PLU/EAN sales report
by specied range
PLU/EAN report by
associated dept.
PLU/EAN pickup report
PLU/EAN zero sales
report
PLU/EAN zero sales
report by associated dept.
All clerk report
Individual clerk report
Hourly report (by specied
range)
Hourly report (all)
Daily net report
Flash report
4. Install two new LR6(“AA” size) batteries into the
battery compartment.
5. Close the battery cover.
6. Replace the printer cover.
Paper Roll
When colored dye appears on the edges of the paper
roll, it is time to replace the paper roll.
Use paper of 57.5 ± 0.5 mm in width. To prevent
jamming be sure to use paper specied by SHARP.
Replacement (Receipt)
1. Conrm that the REG mode has been selected.
2. Remove the printer cover.
3. Lift up the print roller arm of the receipt side.
4. Remove the paper roll from the paper roll cradle
of the receipt side.
D
Do not pull the paper through the printer.
5. Install a new paper roll correctly by following the
steps in “Installing Paper Rolls”.
Replacement (Journal)
1. Conrm that the REG mode has been selected.
2. Remove the printer cover.
3. Press the journal paper feed key to advance the
journal paper until its printed part is out of the way.
4. Cut the paper and remove the take-up spool from
the bearing.
5. Lift up the print roller arm of the journal side.
6. Remove the paper roll from the paper roll cradle
of the journal side.
7. Remove the paper holding plate of the take-up spool.
8. Remove the printed journal roll from the take-up
spool.
D
Do not pull the paper through the printer.
9. Install a new paper roll correctly by following the
steps in “Installing Paper Rolls”.
Removing a Paper Jam
D
The paper cutter is mounted on the printer
cover. Be careful not to cut yourself Never
touch the print head immediately after
printing, as the head may still be hot.
1. Remove the printer cover.
2. Lift up the print roller arm.
3. Remove the paper jam. Check for and remove any
shreds of paper that may remain in the printer.
4. Reset the paper roll correctly by following the
steps in “Installing Paper Rolls”.
Drawer Handling
Locking the Drawer
Develop the habit of locking the drawer when not
using the register for any extended period of time.
To lock: Insert the key into the drawer lock and
turn it 90 degrees counter-clockwise.
To unlock: Insert the key into the drawer lock and
turn it 90 degrees clockwise.
Removing the Drawer
To remove the drawer, pull it out and lift it up.
Drawer
Till
Coin case
D
To prevent burglary, it is a good idea to
empty the drawer after work and leave it
open at the end of the day.
Coin case is detachable.
Manually Opening the Drawer
In case of a power failure or if the machine is out of
order, locate the lever at the bottom of the machine
and move it in the direction of the arrow to open the
drawer. The drawer will not open if it is locked with
the drawer lock key.
Lever
Installing the Fixing Angle Bracket
To prevent the register from moving when the drawer
opens, the xing angle bracket is supplied with the
register. By attaching the bracket to the table where
the register is installed, you can hook the register on
this bracket and secure the register to its position.
How to install the xing angle bracket
1. Thoroughly clean the location where the xing
angle bracket (B) is to be placed.
2. Peel off the adhesive tape on the xing angle
bracket.
3. Hook the angle bracket onto the hook (A) that
is located at the bottom rear of the register.
4. Firmly stick the xing angle bracket to the
table surface that your cleaned above.
How to remove the register from the
xing angle bracket
Lift up the front of the register and pull the register
towards you.
D
When both sales quantities and sales
amounts are zero, printing is skipped.
If you do not want to skip, change the
programming. For details, refer to “FULL
DETAILED INSTRUCTION MANUAL”.
“X” represents read symbol and “Z”
represents reset symbol in the reports.
The drawer does not open when you take
X/Z reports.
When printing is performed continuously,
the printing may be intermitted for several
seconds. After the intermission, the
printing will be restarted.
How to take a X1/Z1 or X2/Z2 report
[To take an X1 or X2 report:]
1. Press the
key.
2. Select the “4 X1/Z1 MODE” or “5 X2/Z2 MODE”
by using the key, and press the
A
key.
3. Select “2 READING” in the X1/Z1 mode or
select “1 READING” in the X2/Z2 mode menu
window and press in both cases the
A
key to
display the items list.
4. Select the appropriate report title.
5. Press the
A
key.
[To take a Z1 or Z2 report:]
1. Press the
key.
2. Select the “4 X1/Z1 MODE” or “5 X2/Z2 MODE”
by using the key, and press the
A
key.
3. Select “3 RESETTING” in the X1/Z1 mode
or select “2 RESETTING” in the X2/Z2 mode
menu window and press in both cases the
A
key to display the items list.
4. Select the appropriate report title.
5. Press the
A
key.
Flash report
You can take ash reports (display only) in the X1
mode for department sales, cash in drawer (CID)
and sales total at the point you take the report.
1. Press the key.
2. Select “1 FLASH READ” in the X1/Z1 mode
menu window and press the
A
key to display
the items list.
3. Select “DEPT. SALES” to take a ash report of
department sales, “CID” to take a ash report
of cash in drawer, or “SALES TOTAL” to take a
ash report of sales total.
4. Press the
A
key.
6. Cut off the excess paper.
7. Press the receipt paper feed key to make sure
the paper end comes out of the printer cover
and clean paper appears.
D
If the paper end does not come out, open
the printer cover, and pass the paper end
between the paper cutter and the paper
guide of the printer cover, and replace the
printer cover.
Installing the journal paper roll
1. Remove the printer cover.
2. Lift up the print roller arm of the journal side.
Print roller arm
3. Set a paper roll in the paper roll cradle of the
journal side as per the diagram.
4. While holding down the paper, slowly close the
print roller arm of the journal side, and push
down the arm until you hear a click locking the
arm.
Paper positioning
guides
5. Remove the paper holding plate from the
spool.
Insert the end of the paper into the slit in the
spool. (Press the journal paper feed key to
feed more paper if required.)
Spool
Paper holding
plate
Wind the paper two or three turns around
the spool shaft.
6. Mount the paper holding plate onto the take-
up spool.
Set the spool on the bearing, and press the
journal paper feed key to take up excess
slack in the paper.
7. Replace the printer cover.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp XE-A307 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp XE-A307 in the language / languages: English as an attachment in your email.

The manual is 3,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp XE-A307

Sharp XE-A307 User Manual - English - 146 pages

Sharp XE-A307 User Manual - German - 147 pages

Sharp XE-A307 User Manual - Dutch - 146 pages

Sharp XE-A307 User Manual - Dutch - 2 pages

Sharp XE-A307 User Manual - French - 147 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info