34019
62
Zoom out
Zoom in
Previous page
1/106
Next page
61
Using external equipment
Setting the recording mode (i.LINK)
The function for automatically adjusting the recording
mode of connected D-VHS decks can be turned on
or off.
• Since most of the currently available D-VHS decks
automatically recognize the transfer rates of the
pictures and sound being recorded and control the
recording mode accordingly, you should always set
this Mode to “Pass thru” in normal circumstances.
Depending on the D-VHS deck used and the type of
broadcast being recorded, this System may not
adjust the recording mode properly. In this case,
please set the “Recording Mode” to “Pass thru”.
Press MENU and the MENU screen displays.
Press c/d to select “Digital Setup”.
Press a/b to select “i.LINK Setup”, and then
press ENTER.
1
2
3
Press a/b to select “Recording Mode”, and
then press ENTER.
4
Press c/d to select “Auto” or “Pass thru”,
and then press ENTER.
Normally, this should be set to “Pass thru”.
5
Setting the Standby Mode (i.LINK)
Power consumption during standby mode can be
minimized by changing the setting of the “Standby
Mode” in “i.LINK Setup”.
When i.LINK is not in use, select “Inactive” in
“Standby Mode”.
Press MENU and the MENU screen displays.
Press c/d to select “Digital Setup”.
Press a/b to select “i.LINK Setup”, and then
press ENTER.
1
2
3
Press a/b to select “Standby Mode”, and
then press ENTER.
4
Press c/d to select “Active” or “Inactive”,
and then press ENTER.
5
“Active”: Power continues to pass through the i.LINK
circuit so data can be relayed.
“Inactive”: Power consumption is minimized during
stand-by mode. Data cannot be relayed at this
setting.
NOTE
When the main power of the System is in standby mode
(POWER indicator lights off), i.LINK control commands
cannot be received from a D-VHS deck. This does not
change even if the “Standby Mode” is set to “Active”. To
control the System from a D-VHS deck, turn the System
power on (POWER indicator lights up in blue).
Data cannot be relayed between i.LINK devices when all
the following conditions are met: 1) More than one i.LINK
device is connected to the System with i.LINK cables, 2)
“Standby Mode” is set to “Inactive”, and 3) The power of
the System is in standby mode (POWER indicator lights
off). When the System is connected between two i.LINK
devices in series, select “Active” in “Standby Mode” or
connect the System at an end of the series as shown in
the diagram.
LC-45GX6U(E)-060-065 04.7.8, 8:52 AM61
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp TUGD10UT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp TUGD10UT in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 5,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info