19053
23
Zoom out
Zoom in
Previous page
1/78
Next page
E-18
SD_HX600_SEC_SECL_E1.fm04/3/15
ENGLISH
TINSKA016AWZZ
F
S
V
I
N
P
E
E
SD-HX600
Preparation for Use
- Remote control / AC power connection -
Remote control
! Battery installation
Precautions for battery use:
" Replace all old batteries with new ones at the same time.
" Do not mix old and new batteries.
" Remove the batteries if the unit will not be used for long periods of time. This will
prevent potential damage due to battery leakage.
Caution:
" Do not use rechargeable batteries (nickel-cadmium battery, etc.).
" Installing the batteries incorrectly may cause the unit to malfunction.
Notes concerning use:
" Replace the batteries if the operating distance is reduced or if the operation
becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).
" Periodically clean the transmitter on the remote control and the sensor on the unit
with a soft cloth.
" Exposing the sensor on the unit to strong light may interfere with operation.
Change the lighting or the direction of the unit.
" Keep the remote control away from moisture, heat, shock, and vibrations.
! Test of the remote control
AC power connection
! Connecting the AC power cord
After checking all the connections have been made correctly, plug the AC power cord
of the amplifier unit and the AV selector into the AC outlet.
Note:
Unplug the AC power cord from the AC outlet if the unit will not be in use for a pro-
longed period of time.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
! To turn the power on
If the power does not turn on, check if the power cords are plugged in properly.
To set the main unit and amplifier unit to stand-by mode:
Press the ON/STAND-BY button on the main unit again.
To turn off the AV selector:
Press the POWER button on the AV selector again.
Notes:
" After the main unit and amplifier unit enters the power stand-by mode, wait a few
seconds to turn on again.
" To turn on the main unit, you can also use the ON/STAND-BY button on the
remote control.
" You cannot turn on/off the AV selector with the ON/STAND-BY button on the
remote control.
1 Open the battery cover.
2 Insert the supplied batteries
according to the direction in-
dicated in the battery com-
partment.
When inserting or removing the bat-
teries, push them toward the bat-
tery terminals.
3 Close the cover.
Point the remote control directly at the re-
mote sensor on the main unit.
The remote control can be used
within the range shown on the
right.
Press the ON/STAND-BY button. Does
the power turn on? Now, you can enjoy
your system.
Note:
The remote control may not work while the
disc door is open. Move closer to the main
unit, or aim the remote control from differ-
ent angles.
8" - 20'
(0.2 m - 6 m)
Remote
sensor
Main unit
1 Press the POWER button on the AV selector.
2 Press the ON/STAND-BY button on the main unit.
AC outlet
(AC 120 V, 60 Hz)
Main unit
AV selector
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp SDHX600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp SDHX600 in the language / languages: English, French as an attachment in your email.

The manual is 6,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info