Manual Sharp SDHX500 (page 4 of 72) (English, French)

19055

Zoom out

Zoom in

1/72

iii

01/12/7 SD-HX500_SEC_SECL_common.fm

TINSKA015AWZZ

IMPORTANT SAFETY INSTRUCTIONS

(for Users in the U.S.A.) (continued)

15 Outdoor Antenna Grounding - If an outside antenna or cable system

is connected to the product, be sure the antenna or cable system is

grounded so as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical Code, ANSI/

NFPA 70, provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire to an an-

tenna discharge unit, size of grounding conductors, location of antenna-

discharge unit, connection to grounding electrodes, and requirements

for the grounding electrode.

16 Lightning - For added protection for this product during a lightning

storm, or when it is left unattended and unused for long periods of

time, unplug it from the wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product due to lightning and

power-line surges.

17 Power Lines - An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits,

or where it can fall into such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from

touching such power lines or circuits as contact with them might be

fatal.

Overloading - Do not overload wall outlets, extension cords, or integral

convenience receptacles as this can result in a risk of fire or electric shock.

19 Object and Liquid Entry - Never push objects of any kind into this

product through openings as they may touch dangerous voltage points

or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the product.

20 Servicing - Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service personnel.

21 Damage Requiring Service - Unplug this product from the wall outlet

and refer servicing to qualified service personnel under the following

conditions:

a)When the power-supply cord or plug is damaged,

b)If liquid has been spilled, or objects have fallen into the product,

c)If the product has been exposed to rain or water,

d)If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the op-

erating instructions as an improper adjustment of other controls may

result in damage and will often require extensive work by a qualified

technician to restore the product to its normal operation,

e)If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance - this

indicates a need for service.

22 Replacement Parts - When replacement parts are required, be sure

the service technician has used replacement parts specified by the

manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock, or other

hazards.

23 Safety Check - Upon completion of any service or repairs to this prod-

uct, ask the service technician to perform safety checks to determine

that the product is in proper operating condition.

24 Wall or Ceiling Mounting - The product should be mounted to a wall

or ceiling only as recommended by the manufacturer.

25 Heat - The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products (including ampli-

fiers) that produce heat.

ANTENNA LEAD IN WIRE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC - NATIONAL ELECTRICAL CODE

S2898A

ELECTRIC

SERVICE

EQUIPMENT

GROUND

CLAMP

Example of antenna grounding as per

National Electrical Code, ANSI/NFPA 70

ANTENNA DISCHARGE UNIT

(NEC SECTION 810-20)

0109

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sharp SDHX500 in the language / languages: English, French as an attachment in your email.

The manual is 5,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sharp SDHX500 Manual

Product: