19051
15
Zoom out
Zoom in
Previous page
1/30
Next page
15
SD-EX200
03/3/14
SD-EX200_sec.fm
TINSZ0523AWZZ
2
3
4
5
6
7
8
1
Preparation for Use
- Setting the clock -
Setting the clock
By setting the unit to the correct time, you can use it not only as a clock but also for
timer playback.
In this example, the clock is set for the 12-hour (AM 12:00) display.
[When the power is on]
Press the TIMER button.
Within 10 seconds, press the CURSOR ( or ) button to display the time.
The time display will appear for about 10 seconds.
Note:
The "CLOCK" will appear at the push of the DISPLAY button when the AC power sup-
ply is restored after a power failure or unplugging the unit.
Readjust the clock as follows.
To readjust the clock:
Perform "Setting the clock" from the beginning.
To change the 12-hour or 24-hour display:
1
Press the ON/STAND-BY button to turn the power on.
2
Press the TIMER button.
3
Within 10 seconds, press the CURSOR ( or ) button to select
"CLOCK", and press the ENTER button.
4
Press the CURSOR ( or ) but-
ton to select 12-hour or 24-
hour display and then press
the ENTER button.
"AM 12:00" The 12-hour display will appear. (AM 12:00 - PM 11:59)
"AM 0:00" The 12-hour display will appear. (AM 0:00 - PM 11:59)
"0:00" The 24-hour display will appear. (0:00 - 23:59)
Note that this can only be set when the unit is first installed or it has been reset.
[Refer to "Clearing all the memory (reset)" on page 27 for details.]
5
Press the CURSOR ( or ) but-
ton to adjust the hour and then
press the ENTER button.
z Press the CURSOR ( or ) button once to advance the time by 1 hour. Hold
it down to advance continuously.
z When the 12-hour display is selected, "AM" will change automatically to "PM".
6
Press the CURSOR ( or ) but-
ton to adjust the minutes and
then press the ENTER button.
z Press the CURSOR ( or ) button once to advance the time by 1 minute.
Hold it down to advance by 5 minutes.
z The hour will not advance even if minutes advance from "59" to "00".
z The clock begins counting from "0" seconds. (Seconds are not displayed.)
The time display will disappear after a few seconds.
To confirm the time display:
[When the unit is in the stand-by mode]
Press the DISPLAY button on the remote control.
The time display will appear for about 5 seconds.
1. Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on
page 27 for details.]
2. Perform "Setting the clock" from the beginning.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp SDEX200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp SDEX200 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info