564581
18
Zoom out
Zoom in
Previous page
1/20
Next page
GB-17
TROUBLESHOOTING
TROUBLESHOOTING CHART
QUERY ANSWER
Draught circulates around the door. When the oven is working, air circulates within the cavity.
The door does not form an airtight seal so air may escape from the door.
Condensation forms in the oven,
and may drip from the door.
The oven cavity will normally be colder than the food being cooked, and so steam produced when
cooking will condense on the colder surface. The amount of steam produced depends on the water
content of the food being cooked. Some foods, such as potatoes have a high moisture content.
Condensation trapped in the door glass should clear after a few hours.
Flashing or arcing from within the
cavity when cooking.
Arcing will occur when a metallic object comes into close proximity to the oven cavity during cooking.
This may possibly roughen the surface of the cavity, but would not otherwise damage the oven.
Arcing potatoes. Ensure all "eyes" are removed from the potatoes and that they have been pierced, place directly onto
the turntable or in a heat resistant  an dish or similar.
The display is lit but the control
panel will not work when pressed.
Check the door is closed properly.
Oven cooks too slowly. Ensure correct power level has been selected.
Oven makes a noise. The microwave energy pulses ON and OFF during cooking/defrosting.
Outer cabinet is hot. The cabinet may become warm to the touch - keep children away.
WARNING: Never adjust, repair or modify the oven yourself. It
is hazardous for anyone other than a SHARP trained engineer
to carry out servicing or repairs.
This is important as it may involve the removal of covers that
provide protection against microwave energy.
The door seal stops microwave leakage during oven operation, but
does not form an airtight seal. It is normal to see drops of water,
light or feel warm air around the oven door. Food with a high
moisture content will release steam and cause condensation inside
the door which may drip from the oven.
Repairs and Modi cations: Do not attempt to operate the oven if
it is not working properly.
Outer Cabinet & Lamp Access: Never remove the outer cabinet.
This is very dangerous due to high voltage parts inside which must
never be touched, as this could be fatal.
Your oven is not  tted with a lamp access cover. If the lamp fails, do
not attempt to replace the lamp yourself, call a SHARP approved
service facility.
If you think the oven is not working properly there are some simple
checks you can carry out yourself before calling an engineer. This
will help prevent unnecessary service calls if the fault is something
simple.
Follow this simple check below:
Place half a cup of water on the turntable and close the door.
Programme the oven to cook for 1 minute using 100% microwave
power.
1. Does the oven lamp come on when it is cooking?
2. Does the turntable rotate?
3. Does the cooling fan work? (Check by placing your hand above
the air vent openings.)
4. After 1 minute does the audible signal sound?
5. Is the water in the cup hot?
If you answer “NO” to any question first check that the oven is
plugged in properly and the fuse has not blown. If there is no
fault with either, check against the troubleshooting chart below.
TO REPLACE THE MAINS PLUG
IMPORTANT
The fuse from the cut-o plug should be removed and the plug
disposed of in a safe manner.
Under no circumstances should the cut-o plug be inserted into
a socket outlet as a serious electric shock may occur.
The plug must not be used without the fuse cover  tted.
If you have any doubt about your microwave oven obtain the help
of a qualified electrician. When replacing the plug please ensure
that you use a BSI or ASTA approved plug to BS1363, this should be
tted with a brown coloured 13 amp fuse approved by BSI or ASTA
to BSI 362. If you have any doubt about electrical connection seek
the help of a quali ed electrician.
The wires in the mains cable are colour coded as shown:
Green and yellow stripes = EARTH
Blue = NEUTRAL
Brown = LIVE
As the colours in the mains lead of your oven may not correspond
with the coloured marking identifying the terminals in your plug,
connect the wires as described:
The green and yellow wire to the plug terminal marked E or
or coloured green or coloured green and yellow.
The blue wire to the plug terminal marked N or coloured black or
coloured blue.
The brown wire to the plug terminal marked L or coloured red or
coloured brown.
Make sure the terminal screws are tight and the cable is held
securely by the cable grip where it enters the plug.
Like most appliances in your home, your oven must be connected to a
single phase 230-240V~, 50Hz alternating current supply.
If you do not make the proper electrical connections you might
damage the oven or injure yourself. Neither SHARP nor the supplier
will be liable if this happens.
WARNING: THIS APPLIANCE MUST BE EARTHED
If you have any doubts about your electrical supply ask a
quali ed electrician.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp R-622STM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp R-622STM in the language / languages: English as an attachment in your email.

The manual is 4,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info