526683
15
Zoom out
Zoom in
Previous page
1/75
Next page
Introduction Easy Start Setup
Connections
Basic
Operation
Useful
Features
Appendix
OPERATION MANUAL
DATA PROJECTOR
MODEL
PG-LW2000
ii
IMPORTANT
For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
Before recycling the packag ing, please
ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page
3.
Model No.:
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating
a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse
marked
or and of the same rating as above, which is also indicated on the pin face
of the plug, must be used.
Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fi tted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-
ately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fi t an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol
or coloured green
or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
1
Introduction
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new
SHARP Projec tor, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefi t of the parts,
service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety noti cation of inspection,
modifi cation, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is
provided to ensure that the device complies with FCC Class A verifi cation.
U.S.A. ONLY
WARNING:
FCC Regulations state that any unauthorized changes or modifi cations
to this equipment not expressly approved by the manufacturer could
void the user's authority to operate this equip ment.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
The lightning fl ash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
be of suffi cient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the pres-
ence of important operating and main-
tenance (servicing) instructions in the
literature accompanying the product.
See bottom of projector.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
WARNING:
To reduce the risk of fi re or electric shock, do not
expose this product to rain or mois ture.
WARNING:
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
2
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact
your local authorities, the Electronics Industries Alliance: www.eiae.org,
the lamp recycling organization www.lamprecycle.org, or Sharp at
1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
fully cool before removing the lamp unit.
Do not touch the glass surface of the lamp unit or the inside of the projector.
Do not loosen other screws except for the lamp unit cover and lamp unit.
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the lamp to become damaged or explode.
Carefully change the lamp by following the instructions described on pages
56 to 58.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
3
Introduction
Accessories
Supplied accessories
Power cord*
For U.S. and
Canada, etc.
(6' (1.8 m))
<QACCDA083WJPZ>
For Europe,
except U.K.
(6' (1.8 m))
<QACCVA025WJPZ>
For U.K. and
Singapore
(6' (1.8 m))
<QACCBA105WJPZ>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA056WJPZ>
(1) (2) (3) (4)
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country.
Initial setup guide <TINS-F582WJZZ>
CD-ROM <UDSKAA137WJN1>
Remote control
<RRMCGB015WJSA>
Two LR03 batteries
(“AAA” size, UM/SUM-4,
HP-16 or similar)
RGB cable
(6' (1.8 m))
<QCNWGA173WJPZ>
Codes in “< >” are Replacement parts codes.
Note
Optional accessories
Lamp unit
Ceiling-mount adaptor
Ceiling-mount bracket
Ceiling-mount unit
Ceiling-mount extension tube
3 RCA to mini D-sub 15 pin cable (10 n (3.0 m))
AN-LX20LP
AN-60KT
AN-XRCM30 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XRCM30>
(for U.S.A. only)
AN-C3CP2
Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
Note
4
Contents
Preparing
Introduction
Accessories ............................................3
Contents .................................................4
IMPORTANT SAFEGUARDS ..................6
Part Names and Functions ...................10
Top View ................................................ 10
Front View .............................................. 10
Rear View (Terminals) .............................. 11
Inserting the Batteries ............................. 13
Usable Range ......................................... 13
Easy Start
Easy Start .............................................14
Setup and Projection .............................. 14
Setup
Setting Up the Projector .......................16
Video Setup............................................ 16
Setting Up the Projector ......................... 16
Standard Setup (Front Projection) ........... 16
Screen Size and Projection Distance ...... 17
Projection (PRJ) Mode ............................ 18
Ceiling-Mount Setup ............................... 18
Connections
Connecting the Projector to
Other Equipment ................................19
Connecting the Power Cord .................21
Controlling the Projector by
a Computer ........................................22
Useful Features
Operating with the Remote Control......30
Displaying and Setting the
Break Timer ......................................... 30
Displaying the Pointer ............................. 30
Using the Spot Function ......................... 30
Switching the Eco+Quiet Mode .............. 30
Auto Sync (Auto Sync Adjustment) ......... 31
Freezing a Moving Image ........................ 31
Selecting the Picture Mode ..................... 31
Displaying an Enlarged Portion of
an Image ............................................. 31
Menu Items ...........................................32
Using the Menu Screen ........................35
Menu Selections (Quick Start Menu) .........35
Quick Start Menu .................................... 36
Menu Selections (Complete Menu) .......... 36
Picture Adjustment (“Picture” Menu) ....38
Selecting the Picture Mode ..................... 38
Adjusting the Image ................................ 39
Adjusting the Color Temperature ............. 39
Adjusting the Colors ............................... 39
Selecting the Film Mode ......................... 40
Reducing Image Noise (DNR) ................. 40
Eco+Quiet .............................................. 40
Signal Adjustment (“SIG-ADJ” Menu) ..41
Adjusting the Computer Image ............... 41
Resolution Setting .................................. 41
Signal Type Setting ................................. 41
Selecting the Dynamic Range ................. 41
Setting the Video System ....................... 42
Setting the Video Setup .......................... 42
Checking the Input Signal ....................... 42
Adjusting the Projected Image
(“SCR-ADJ” Menu) .............................43
Setting the Resize Mode ......................... 43
Adjusting the Image Position .................. 43
Keystone Correction ............................... 43
Setting the Overscan .............................. 44
Setting the On-screen Display ................ 44
Closed Caption ...................................... 44
Selecting the Background Image ............ 45
Selecting the Setup Guide ...................... 45
Reversing/Inverting Projected Images ..... 45
Selecting the Wall Color .......................... 45
Selecting the On-screen Display Language
... 45
Adjusting the Projector Function
(“PRJ-ADJ1/2” Menu) ........................46
Auto Sync (Auto Sync Adjustment) ......... 46
Auto Power Off Function ........................ 46
Auto Restart Function ............................. 46
Speaker Setting ...................................... 46
Fan Mode Setting ................................... 46
System Lock Function ............................ 47
Using
Basic Operation
Turning the Projector On/Off ................23
Turning the Projector On ......................... 23
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 23
Image Projection ..................................24
About the Setup Guide ........................... 24
Adjusting the Projected Image ................ 24
Correcting Trapezoidal Distortion ............ 26
Switching the Input Mode ....................... 27
Adjusting the Volume .............................. 27
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 27
Resize Mode .......................................... 28
5
Introduction
Keylock Function .................................... 48
Selecting the Quick Start Menu .............. 49
Setting the FUNCTION Button Operation
.. 49
STANDBY Mode ..................................... 49
DLP
®
Link
TM
............................................ 49
DLP
®
Link
TM
Invert .................................. 49
Returning to the Default Settings ............ 49
Checking the Lamp Life Status ............... 49
Viewing Stereoscopic 3D Images .........50
Precautions on Viewing Stereoscopic
3D Images ........................................... 50
Information on the 3D Projection
Function .............................................. 51
Appendix ................................................ 51
Using 3D Viewing Mode ......................... 52
Reference
Appendix
Maintenance .........................................53
Maintenance Indicators ........................54
Regarding the Lamp .............................56
Lamp ...................................................... 56
Caution Concerning the Lamp ................ 56
Replacing the Lamp ............................... 56
Removing and Installing the Lamp Unit ... 57
Resetting the Lamp Timer ...................... 58
RS-232C Specifi cations and Commands
...59
Compatibility Chart ..............................64
Troubleshooting ....................................66
For SHARP Assistance .........................69
Specifi cations .......................................70
Dimensions ...........................................71
Index .....................................................72
In this operation manual, the illustration and the screen display are simplifi ed for explanation, and
may differ slightly from the actual display.
6
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its
installation, use and servicing.
1. Read Instructions
All the safety and operating instructions
should be read before the product is
operated.
2. Retain Instructions
The safety and operating instructions
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should
be followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer's instructions, and should use a
mounting accessory recom mended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered. The open ings should never be
blocked by placing the product on a bed, sofa,
rug, or other similar surface. This prod uct
should not be placed in a built-in installation
such as a book case or rack unless proper
ventilation is provided or the manufacturer's
in struc tions have been adhered to.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
com pany. For products intended to operate
from battery power, or other sources, refer
to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the
following types of plugs. If the plug should
fail to fi t into the power outlet, please contact
your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug
with a grounding terminal.
This plug will only fi t into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and the
point where they exit from the product.
14. Lightning
For added protection for this product during
a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the cable system. This will
pre vent damage to the product due to
lightning and power-line surges.
7
Introduction
15. Overloading
Do not overload wall outlets, extension cords,
or integral convenience receptacles as this
can result in a risk of fi re or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fi re or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dan ger ous voltage or
other hazards. Refer all servicing to
qualifi ed service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualifi ed service
person nel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those con trols that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
quali ed technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a
need for service.
19. Replacement Parts
When replacement parts are required, be
sure the service technician has used
replace ment parts specifi ed by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in
re, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs
to this product, ask the service technician
to per form safety checks to determine that
the product is in proper operating
condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall
or ceiling only as recommended by the
manufacturer.
22. Heat
This product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products
(including amplifi ers) that produce heat.
DLP
®
and the DLP logo are registered trademarks of Texas Instruments and
BrilliantColor
TM
and DLP
®
Link
TM
are trademarks of Texas Instruments.
PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
Macintosh
®
is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
All other company or product names are trademarks or registered trademarks of their
respective companies.
Some IC chips in this product include confi dential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
8
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
on page
56.
Caution concerning the setup of the
projector
For minimal servicing and to maintain high
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be performed by a Sharp
Authorized Projector Dealer or Service
Center.
Rest your eyes occasionally.
Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing diffi cult. Close the curtains
and dim the lights when setting up the
screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
After the projector is purchased, a faint
smell from the vent may appear when the
power is fi rst turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
When using the projector in high-
altitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Warning about placing the projector in
a high position
When placing the projector in a high
position, make certain it is carefully secure
to avoid personal injury caused by the
projector falling down.
Do not subject the projector to hard
impact and/or vibration.
Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
Allow at least 11
13
/
16
inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
Ensure that the intake vent and the exhaust
vent are not obstructed.
If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
malfunction. (See pages 54 and 55.)
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
9
Introduction
Caution regarding usage of the projector
If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other
cables connected to it.
Do not carry the projector by holding the
lens.
Do not expose the projector to direct
sunlight or place next to heat sources.
Doing so may affect the cabinet color or
cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other
audio-visual equipment to the projector,
make the connections AFTER unplugging
the power cord of the projector from the
AC outlet and turning off the equipment to
be connected.
Please read the operation manuals of the
projector and the equipment to be
connected for instructions on how to make
the connections.
Using the projector in other countries
The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
If the temperature inside the projector
increases, due to blockage of the air vents,
or the setting location, the temperature
warning indicator will blink. And if the
temperature keeps on rising, “ ” will
illuminate in the lower left corner of the
picture with the temperature warning
indicator blinking. If this state continues,
the lamp will turn off, the cooling fan will
run and then the projector will enter
Standby mode. Refer to “Maintenance
Indicators” on pages 54 and 55 for details.
Info
The cooling fan regulates the internal
temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this
license (“Fonts”) and associated documentation fi les (the “Font Software”), to reproduce and distribute the
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one
or more of the Font Software typefaces.
The Font Software may be modifi ed, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts,
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modifi ed and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further
information, contact: fonts at gnome dot org.
10
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
13
11
12
1
2
5
6
3
4
7
9
8
10
14
15 16 17
Front View
1 Temperature warning indicator
54
2 Lamp indicator
54
3 Power indicator
54
4 STANDBY/ON button
23
For turning the power on and putting the
projector into Standby mode.
5 ENTER button
35
For setting items selected or adjusted on
the menu.
6 VOL (Volume) buttons (–O/Q+)
27
For adjusting the speaker sound level.
7 AUTO SYNC button
31
For automatically adjusting images when
connected to a computer.
8 Adjustment buttons (P/R/O/Q)
35
For selecting menu items.
9 INPUT buttons (P/R)
27
For switching Input mode.
10 MENU button
35
For displaying adjustment and setting
screens.
Top View
11 Zoom ring
25
For enlarging/reducing the picture.
12 Focus ring
24
For adjusting the focus.
13 Intake vent
53
14 Security bar
15 HEIGHT ADJUST lever
25
16 Adjustment foot
25
17 Remote control sensor
13
11
Introduction
1234 5
8
9
10
6
7
Rear View (Terminals)
1 HDMI terminal
19, 20, 21
Terminal for HDMI input.
2 AUDIO input terminal
21
3 VIDEO input terminal
20
Terminal for connecting video equipment.
4 COMPUTER/COMPONENT input
terminal
19, 20
Terminal for computer RGB and
component signals.
5 RS-232C terminal
22
Terminal for controlling the projector using
a computer.
6 Exhaust vent
53
7 Speaker
46
8 Kensington Security Standard
connector
9 Rear adjustment foot
25
10 AC socket
21
Connect the supplied power cord.
Using the Kensington Lock
This projector has a Kensington Security
Standard connector for use with a
Kensington MicroSaver Security System.
Refer to the information that came with the
system for instructions on how to use it to
secure the projector.
13
Introduction
Inserting the Batteries
1
Pull down the tab on the cover and remove the
cover towards the direction of the arrow.
2
Insert the batteries.
Insert the batteries making sure the polarities correctly match
the m and n marks inside the battery compartment.
3
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode.
Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then
remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
1
2
3
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
The signal from the remote control can be
refl ected off a screen for easy operation.
However, the effective distance of the signal
may differ depending on the screen material.
Note
When using the remote control
Ensure that you do not drop it or expose it to
moisture or high temperature.
The remote control may malfunction under a
uorescent lamp. In this case, move the
projector away from the fl uorescent lamp.
Remote control sensor
Remote control signal
transmitters
Remote control
33n (10 m)
30°
30°
Remote control sensor
Remote control signal
transmitters
Remote control
33n (10 m)
30°
30°
14
Easy Start
This section shows the basic operation (projector connecting with the computer). For details,
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
STANDBY button
8
KEYSTONE button
5
3
ON button
6
INPUT buttons
5
Adjustment
buttons
(P/R/O/Q)
O/Q buttons
6
STANDBY/ON
button
3
8
Focus ring
4
HEIGHT
ADJUST lever
4
Zoom ring
4
INPUT buttons
6
6
1. Place the projector facing a wall or a screen
_
P. 16
When connecting equipment other than a computer, see pages
20 and 21.
2. Connect the projector to the computer and plug the power
cord into the AC socket of the projector
_PP. 19, 21
Press STANDBY/ON on the projector or ON on the remote control.
3. Turn the projector on
_P. 23
17
Setup
Screen Size and Projection Distance
Screen
Lens center
H
L
16:10 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Diag. [
χ
] Width Height Minimum [L1] Maximum [L2]
300" (762 cm) 646 cm (254") 404 cm (159") 10.0 m (32' 9") 12.0 m (39' 6") 7 cm (2
37
/
64
")
250" (635 cm) 538 cm (212") 337 cm (132") 8.3 m (27' 4") 10.0 m (32' 11") 5 cm (2
9
/
64
")
200" (508 cm) 431 cm (170") 269 cm (106") 6.7 m (21' 10") 8.0 m (26' 4") 4 cm (1
23
/
32
")
150" (381 cm) 323 cm (127") 202 cm (79") 5.0 m (16' 5") 6.0 m (19' 9") 3 cm (1
9
/
32
")
120" (305 cm) 258 cm (102") 162 cm (64") 4.0 m (13' 1") 4.8 m (15' 10") 3 cm (1
1
/
32
")
100" (254 cm) 215 cm (85") 135 cm (53") 3.3 m (10' 11") 4.0 m (13' 2") 2 cm (0
55
/
64
")
80" (203 cm) 172 cm (68") 108 cm (42") 2.7 m (8' 9") 3.2 m (10' 6") 2 cm (0
11
/
16
")
60" (152 cm) 129 cm (51") 81 cm (32") 2.0 m (6' 7") 2.4 m (7' 11") 1 cm (0
33
/
64
")
40" (102 cm) 86 cm (34") 54 cm (21") 1.3 m (4' 4") 1.6 m (5' 3') 1 cm (0
11
/
32
")
4:3 Signal Input (Normal Mode)
Picture (Screen) size Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
Diag. [
χ
] Width Height Minimum [L1] Maximum [L2]
300" (762 cm) 610 cm (240") 457 cm (180") 11.3 m (37' 1") 13.6 m (44' 9") 7 cm (2
29
/
32
")
250" (635 cm) 508 cm (200") 381 cm (150") 9.4 m (30' 11") 11.4 m (37' 3") 6 cm (2
27
/
64
")
200" (508 cm) 406 cm (160") 305 cm (120") 7.5 m (24' 9") 9.1 m (29' 10") 5 cm (1
15
/
16
")
150" (381 cm) 305 cm (120") 229 cm (90") 5.7 m (18' 7") 6.8 m (22' 4") 4 cm (1
29
/
64
")
120" (305 cm) 244 cm (96") 183 cm (72") 4.5 m (14' 10") 5.5 m (17' 11") 3 cm (1
11
/
64
")
100" (254 cm) 203 cm (80") 152 cm (60") 3.8 m (12' 4") 4.5 m (14' 11") 2 cm (0
31
/
32
")
80" (203 cm) 163 cm (64") 122 cm (48") 3.0 m (9' 11") 3.6 m (11' 11") 2 cm (0
25
/
32
")
70" (178 cm) 142 cm (56") 107 cm (42") 2.6 m (8' 8") 3.2 m (10' 5") 2 cm (0
43
/
64
")
60" (152 cm) 122 cm (48") 91 cm (36") 2.3 m (7' 5") 2.7 m (8' 11") 1 cm (0
37
/
64
")
40" (102 cm) 81 cm (32") 61 cm (24") 1.5 m (4' 11") 1.8 m (6' 0") 1 cm (0
25
/
64
")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
16:10 Signal 4:3 Signal
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
L1: Minimum projection distance (m/ft) 0.03328
χ
0.03328
χ
/ 0.3048 0.03768
χ
0.03768
χ
/ 0.3048
L2: Maximum projection distance (m/ft) 0.04013
χ
0.04013
χ
/ 0.3048 0.04543
χ
0.04543
χ
/ 0.3048
H:
Distance from the lens center to the bottom of the image (cm/in)
0.02178
χ
0.02178
χ
/ 2.54 0.02466
χ
0.02466
χ
/ 2.54
χ
: Picture diagonal size : 40
''
-300
''
Allow a margin of error in the values in the
diagrams below.
Note
Allow a margin of error in the values in the
diagrams below.
Note
18
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-
ADJ” menu. See page 45.)
Table mounted, front projection
[Menu item “Front”]
Table mounted, rear projection
(with a translucent screen)
[Menu item “Rear”]
Ceiling mounted, front projection
[Menu item “Ceiling + Front”]
Ceiling mounted, rear projection
(with a translucent screen)
[Menu item “Ceiling + Rear”]
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this
installation. Before mounting the projector, contact your nearest Sharp Authorized Projector
Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold
separately).
19
Connections
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet
and turn off the equipment to be connected. After making all connections, turn on the projector
and then the other pieces of equipment. When connecting a computer, ensure that it is the last
equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before
you turn on the connected equipment.
For more details of connection and cables, refer to the operation manual of the connecting equipment.
You may need other cables or connectors not listed below.
Terminals on the Projector
Equipment
Terminal on
connected equipment
Cable
Terminal on the
projector
Computer
RGB
output
terminal
RGB cable (supplied) COMPUTER/
COMPONENT
HDMI output
terminal
HDMI cable (commercially available) HDMI
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission
may not work property. (The HDMI specifi cation does not support all connections to equipment that
has digital output terminal using a DVIÙHDMI digital cable.)
See page
64 “Compatibility Chart” for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the functions to not work.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP notebook computer). Refer to the specifi c instructions in
your computer's operation manual to enable your computer's external output port.
Note
20
Connecting the Projector to Other Equipment (Continued)
Equipment
Terminal on
connected equipment
Cable
Terminal on the
projector
Video equipment
HDMI output
terminal
HDMI cable (commercially available) HDMI
Component
video output
terminal
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
COMPUTER/
COMPONENT
Video output
terminal
Video cable (commercially available) VIDEO
Camera/Video game
Component
video
output
terminal
Cables for a camera or a video game/3 RCA to
mini D-sub 15 pin cable (optional, AN-C3CP2)
RCA adaptor plug
(commercially available)
COMPUTER/
COMPONENT
Video
output
terminal
Cables for a camera or a video game
VIDEO
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission
may not work property. (The HDMI specifi cation does not support all connections to equipment that
has digital output terminal using a DVIÙHDMI digital cable.)
HDMI (High-Defi nition Multimedia Interface) is a digital AV interface that can deliver a high-defi nition
video signal, multi-channel audio signal, and bi-directional control signal all in just one cable.
Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the
digital video signal does not degrade when transmitted, and a high-quality image with a simple
connection can be enjoyed.
The HDMI terminal does not support the CEC signal.
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fi ts in the projector terminal you want to connect.
The projector does not support RGBC signals via the Euro-scart.
Note
21
Connections
Equipment
Terminal on
connected equipment
Cable
Terminal on the
projector
Audio equipment
ø3.5 mm
audio output
terminal
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
AUDIO
RCA audio
output
terminal
RCA audio cable (commercially available)
Audio
output
terminal
Cables for a camera or a video game
HDMI output
terminal
HDMI cable (commercially available) HDMI
You can select HDMI or AUDIO in the INPUT list. (See page 27.)
Note
This projector is able to process the following signals when connected to HDMI
equipment:
Video signal: For details, see “Digital Support” in the list of “Compatibility Chart” on page 64.
Audio signal: Linear PCM audio
Sampling frequency: 48kHz/44.1kHz/32kHz
Connecting the Power Cord
Plug the supplied power cord into the AC
socket on the rear of the projector. Then
plug into AC outlet.
AC socket
To AC outlet
Power cord
(supplied)
AC socket
To AC outlet
Power cord
(supplied)
23
Basic
Operation
Turning the Projector On/Off
Turning the Projector On
Note that the connections to external
equipment and power outlet should be
done before performing the operations
written below. (See pages
19 to 21.)
Press STANDBY/ON on the projector
or ON on the remote control.
The power indicator illuminates green.
After the lamp indicator illuminates, the projector
is ready to start operation.
About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down
abnormally or the lamp should be
replaced.
When switching on the projector, a slight
ickering of the image may be experienced
within the fi rst minute after the lamp has been
illuminated. This is normal operation as the
lamp's control circuitry is stabilising the lamp
output characteristics. It should not be
regarded as faulty operation.
If the projector is put into Standby mode and
immediately turned on again, the lamp may
take some time to start projection.
When System Lock is set, the keycode input
box appears. To cancel the keycode setting,
input the keycode that you have already set.
See page
47 for details.
Note
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector
or STANDBY on the remote control,
then press that button again while the
confi rmation message is displayed, to
put the projector into Standby mode.
The projector cannot be turned on while cooling.
Info
When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector
automatically turns on when the power cord
is plugged into the AC outlet or the breaker
switch is turned on. (See page
46.)
English is the factory default language. If you
want to change the on-screen display to
another language, change the language
according to the procedure on page
45.
STANDBY/ON button
Lamp indicator
Power indicator
STANDBY
button
ON button
On-screen display (confi rmation message)
Info
Direct Power Off function:
You can unplug the power cord from the AC
outlet even if the cooling fan is still running.
28
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
See page 43 for setting on menu screen.
COMPUTER
NORMAL FULL NATIVE 16:9
4:3 aspect ratio
SVGA (800 × 600)
1068 × 800
1280 × 800
800 × 600
1280 × 720
XGA (1024 × 768) 1024 × 768
SXGA (1152 × 864) 1152 × 864
SXGA+ (1400 × 1050) 1400 × 1050
Other aspect ratios
SXGA (1280 × 1024) 1000 × 800 1280 × 1024
1280 × 720 1280 × 720
1360 × 768 1280 × 722 1360 × 768
1366 × 768 1280 × 720 1366 × 768
1280 × 768 1280 × 768
1280 × 720
1280 × 800 1280 × 800
Input signal Output screen image
Computer Image type NORMAL FULL NATIVE 16:9
Resolution XGA and below
4:3 aspect ratio
*1
Resolution higher than
XGA
*3
SXGA (1280 × 1024)
5:4 aspect ratio
*1
1280 × 720
16:9 aspect ratio
*1
*2
*2
1360 × 768
1366 × 768
16:9 aspect ratio
1280 × 768
15:9 aspect ratio
*1
*2
*1
1280 × 800
16:10 aspect ratio
*2
*1
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
*3 In case SXGA+ input.
RESIZE
button
RESIZE
button
Image Projection (Continued)
29
Basic
Operation
VIDEO/DTV
Input signal Output screen image
Video/DTV Image type NORMAL AREA ZOOM V-STRETCH 16:9
480
I, 480P,
576
I, 576P,
NTSC, PAL,
SECAM
4:3 aspect ratio
*1
Squeeze
*1
Letter box
*1
720P, 1035
I,
1080
I, 1080P
16:9 aspect ratio
*1
*2
16:9 aspect ratio
*1
540P
16:9 aspect ratio
*1
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
*1
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
About Copyrights
When using the Resize function to select an image size with a different aspect ratio to a TV
program or video image, the image will look different from its original appearance. Keep this
in mind while choosing an image size.
The use of the Resize or Keystone Correction function to compress or stretch the image for
commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
30
Operating with the Remote Control
POINTER button
ECO+QUIET button
Adjustment buttons
(P/R/O/Q)
BREAK TIMER button
SPOT button
AUTO SYNC button
FREEZE button
PICTURE MODE button
MAGNIFY buttons
EFFECT button
Displaying and Setting the
Break Timer
1
Press BREAK TIMER.
The timer starts to count down from 5
minutes.
On-screen display
2
Press P/R/O/Q to adjust the
length of the break time.
Increases with P or Q
5 minutes 6 minutes 60 minutes
Shortens with O or R
4 minutes 3 minutes 1 minute
The break time can be set in units of one
minute (up to 60 minutes).
Canceling the break timer display function
Press BREAK TIMER.
The Break Timer is not available while the
projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute
- Input Search
Note
1
2
Displaying the Pointer
1
Press POINTER and press P/R/
O/Q on the remote control to
move the pointer.
Press EFFECT to change the pointer icon
(5 types).
Star
Finger1 Finger2 Heart Underline
2
Press POINTER again.
The pointer will disappear.
Using the Spot Function
1
Press SPOT and press P/R/O/Q
on the remote control to move
the spot area.
Press EFFECT to change the spot area
size (3 types).
1/9 1/25 1/8
2
Press SPOT again.
The spot area will disappear.
Switching the Eco+Quiet
Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
When the Eco+Quiet Mode is set to “ON”, the
sound of the cooling fan will turn down, the power
consumption will decrease, and the lamp life will
extend.
Refer to “Eco+Quiet” on page 40 for details.
Note
1
2
1
2
31
Useful
Features
Auto Sync
(Auto Sync Adjustment)
Auto Sync function works when detecting
input signal after the projector turns on.
Press AUTO SYNC to manually adjust
with Auto Sync function.
When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page
41.)
Note
Freezing a Moving Image
1
Press FREEZE.
The projected image is frozen.
2
Press FREEZE again to return to
the moving image from the
currently connected device.
Selecting the Picture Mode
You can select the appropriate Picture
mode for the projected image, such as
movie or video game.
Press PICTURE MODE.
When pressing PICTURE MODE, the Picture
mode changes in the following order:
STANDARD PRESENTATION MOVIE GAME sRGB
*
See page 38 for details on the Picture mode.
Note
* “sRGB” is displayed only when RGB signal is input.
1
2
Displaying an Enlarged
Portion of an Image
Graphs, tables and other portions of
projected images can be enlarged. This
is helpful when providing more detailed
explanations.
1
Press MAGNIFY on the
remote control.
Enlarges the image.
Pressing
or MAGNIFY enlarges
or reduces the projected image.
×1 ×2 ×3 ×4
Press
.
Press
.
You can change the location of the
enlarged image using P, R, O and Q.
Note
2
Press RETURN on the remote
control to cancel the operation.
The magnifi cation then returns to ×1.
The selectable magnifi cations differ
depending on the input signal.
In the following cases, the image will
return to the normal size (×1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency)
change.
- When the Resize mode is changed.
Note
1
2
32
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
Main menu Sub menu
Picture
Page 38 Page 38
Page 39
Page 39
Page 39
Page 39
Page 39
Page 40
Page 40
+30-30
Contrast
+30-30
+30-30
+30-30
1-1
20
+30-30
+30-30
+30-30
Tint
Color
Sharp
Bright
Film Mode
Eco+Quiet
[On/Off]
Reset
Auto
Off
CLR Temp
BrilliantColor™
C.M.S. Setting [On/Off]
C.M.S.
Standard
Presentation
Movie
Game
sRGB
Picture Mode
Red
Blue
Page 40
DNR Level 1
Level 2
Level 3
C.M.S.-Hue
C.M.S.-Saturation
C.M.S.-Value
Page 39
Page 39
Page 39
Reset
Return
+30-30
R
+30-30
+30-30
+30-30
+30-30
+30-30
C
G
B
Y
M
Reset
“Quick Start Menu
Main menu
Normal
Full
Native
Area Zoom
V-Stretch
Border
16:9
Quick Start Menu
Input Search Start
Resolution
Eco + Quiet
[On/Off]
Resize
Information
Go To Complete Menu
Keystone
-80 +80
Language
Sub menu
Page 36
Page 36
Page 36
Page 36
Page 36
Page 36
Page 36
Page 36
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
Türkçe
Tiếng Việt
33
Useful
Features
“Screen adjustment (SCR-ADJ)” menu
Main menu Sub menu
SCR - ADJ
Page 43
Language
Image Shift
Resize
Page 43
Page 43
Page 44
Page 45
Page 45
Page 45
OSD Display [On/Off]
Page 44
Closed Caption
Page 44
Overscan [On/Off]
Background
PRJ Mode
Logo
Blue
None
Page 45
Wall Color Off
Blackboard
Whiteboard
Page 45
Setup Guide [On/Off]
Off
CC1
CC2
Front
Ceiling + Front
Rear
Ceiling + Rear
Normal
Full
Native
Area Zoom
V-Stretch
Border
16:9
Keystone
-80 +80
Page 43
-40 +40
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
Türkçe
Tiếng Việt
“Signal adjustment (SIG-ADJ)” menu
Main menu Sub menu
SIG-ADJ
Page 41
Page 41
Page 41
Page 41
Page 41
Page 42
Signal Type
Video Setup
Signal Info
Auto
RGB
YPbPr
Resolution
0 IRE
7.5 IRE
Page 42
Page 42
Video System Auto
PAL
SECAM
NTSC4.43
NTSC3.58
PAL-M
PAL-N
PAL-60
+30-30
+60-60
+150-150
+150-150
Clock
Phase
H-Pos
V-Pos
Reset
Dynamic Range Auto
Standard
Enhanced
34
“Projector adjustment (PRJ-ADJ1/2)” menu
System Lock
[Enable/Disable]
Keylock [On/Off]
Page 47
Page 48
Fan Mode
Page 46
Normal
High
Main menu Sub menu
PRJ-ADJ1
Page 46
Speaker [On/Off]
Auto Restart [On/Off]
Page 46
Auto Power Off [On/Off]
Page 46
Page 46
Auto Sync [On/Off]
Page 46
Main menu Sub menu
Page 49
Page 49
Page 49
Page 49
Page 49
Page 49
PRJ-ADJ2
FUNCTION Button
Input Search
Audio Mute
Image Shift
Signal Info
STANDBY Mode
Quick Start
Eco
All Reset
Lamp Timer (Life)
Page 49
DLP
®
Link
TM
[On/Off]
DLP
®
Link
TM
Invert
Quick Start Menu [On/Off]
Page 46
Menu Items
(Continued)
35
Useful
Features
Adjustment buttons
(P/R/O/Q)
ENTER button
RETURN button
Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU button
Adjustment buttons (P/R/O/Q)
MENU button
ENTER button
Menu Selections (Quick Start Menu)
This operation can also be performed by using the buttons on the projector.
1
Press MENU.
The “Quick Start Menu” screen for the
selected Input mode is displayed.
2
Press P or R to select the
desired item, then press ENTER.
3
Press P/R/O/Q to adjust the
item selected, then press
ENTER.
Info
To display the advanced settings and
adjustments, select “Go To Complete Menu”.
Press ENTER to display the Complete Menu
screen.
If you do not want to display the Quick Start
Menu, set “Go To Complete Menu” - “PRJ-ADJ2
- “Quick Start Menu” to “Off. (See page
49.)
1
2
3
Example
SEL./ADJ. ENTER END
Input Search Start
Resolution
Resize
0
Eco+Quiet
Language
Keystone
Information
1024×768
Normal
English
Off
Quick Start Menu
Go To Complete Menu…
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used
functions, or the Complete Menu, which enables advanced settings and adjustments.
38
Picture Adjustment (“Picture” Menu)
Menu operation n Page 36
Q PAGE1 Q PAGE2
Picture Mode
Contrast 0
0
0
0
Bright
Color
Tint
0Sharp
Standard
SEL./ADJ. ENTER END
0
0
Red
Blue
Picture SIG SCR PRJ1 PRJ2
1
2
Picture Mode
CLR Temp
BrilliantColor
TM
C.M.S. Setting
C.M.S.
Standard
Film Mode
Eco+Quiet
0
1
On
Auto
Off
DNR
Level 2
Reset
SEL./ADJ. ENTER END
7
6
5
4
2
3
Picture SIG SCR PRJ1 PRJ2
1
Selecting the Picture Mode
Selectable
items
Description
The default settings of each item when selecting Picture Mode
CLR Temp BrilliantColor
TM
Eco+Quiet
Standard For standard image 0 1 Off
Presentation Brightens portions of image for
more enhanced presentations.
02Off
Movie Gives natural tint to the
projected image.
–1 0 On
Game Gives sharpness to the
projected image.
01Off
*sRGB For high fi delity reproduction of
images from a computer.
––Off
“sRGB” is displayed only when RGB signal is input.
You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
You can also press PICTURE MODE on the remote control to select the Picture mode. (See page 31.)
*sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fi xed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
You cannot set the items, “Red”, “Blue”, “CLR Temp, “BrilliantColor
TM
” and “C.M.S., when “sRGB” is
selected.
Note
Info
When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
40
5
Selecting the Film Mode
This function provides high-quality playback
of images originally projected at 24 fps, such
as movies on DVDs.
Selectable
items
Description
Auto Films are detected automatically.
Off Films are not detected.
This function is available for the following
signals.
With COMPUTER/COMPONENT input:
- 480I
- 576I
- 1035I
- 1080I
With VIDEO input:
- All signals
Note
6
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides
high quality images with minimal dot crawl
and cross color noise.
Selectable
items
Description
Level 1
Sets the DNR level for viewing a
clearer picture.
Level 2
Level 3
This function is not available for some signals.
Note
Picture Adjustment (“Picture” Menu)
(Continued)
Menu operation n Page 36
7
Eco+Quiet
Selectable
items
Brightness and Power consumption
On Approx. 75%
Off 100%
When “Eco+Quiet” is set to “On”, the fan
sound and power consumption are lower than
they are when “Off” is selected. (Projection
brightness decreases as shown in the chart.)
Note
41
Useful
Features
Signal Adjustment (“SIG-ADJ” Menu)
Menu operation n Page 36
0
0
0
0
Phase
Clock
H-Pos
V-Pos
Reset
Auto
1024 x 768
0 IRE
Resolution
Signal Type
Video Setup
Auto
Video System
Standard
Dynamic Range
Signal Info 1024 x 768
H 48.3 kHz / V 60.0 Hz
SEL./ADJ. ENTER END
Pict. SIG-ADJ SCR PRJ1 PRJ2
1
3
6
7
2
4
5
1
Adjusting the Computer Image
If the optimum image cannot be obtained with
Auto Sync adjustment, use the SIG-ADJ function.
Selectable
items
Description
Clock Adjusts vertical noise.
Phase Adjusts horizontal noise (similar to
tracking on your VCR).
H-Pos Centers the on-screen image by
moving it to the left or right.
V-Pos Centers the on-screen image by
moving it up or down.
To reset all adjustment items, select “Reset
and press ENTER.
The adjustable range of “H-Pos” (H-Position)
and “V-Pos” (V-Position) may vary depending
on the screen resolution of the computer.
Note
2
Resolution Setting
Ordinarily, the type of input signal is detected and
the correct Resolution mode is automatically
selected. However, for some signals, the optimal
Resolution mode in “Resolution” may need to be
selected to match the computer display mode.
See “Checking the Input Signal” on page 42
for information on the currently selected input
signal.
Note
3
Signal Type Setting
This function allows you to select the input
signal type RGB or Component for
COMPUTER/COMPONENT.
Selectable
items
Description
Auto Input signals are automatically
recognized as RGB or component.
RGB Set when RGB signals are received.
YPbPr Set when Component signals are
received.
4
Selecting the Dynamic Range
An optimum picture may not be displayed if an
HDMI-capable device’s output signal type and
the projector’s input signal type do not match. If
this should occur, switch “Dynamic Range”.
Selectable
items
Description
Auto In most circumstances, “Auto” should
be selected.
Standard When the black levels of the image
show banding or appear faded, select
the item that results in the best picture
quality.
Enhanced
The Dynamic Range can be selected only
when “HDMI” input mode is selected.
Note
48
7
Keylock Function
Use this function to lock the operation buttons
on the projector.
This function can be set using either the menu
screen or ENTER on the projector.
a
Setting with the menu screen
Selectable
items
Description
On All buttons on the projector, except
STANDBY/ON, are locked.
Off Turns off the Keylock function.
a
Setting with the projector buttons
Locking the Operation Buttons
1
Hold down ENTER on the
projector for about 5 seconds
while the projector is being
turned on.
The Keylock function screen is displayed.
Use this function to lock the operation buttons
on the projector.
(Except STANDBY/ON button)
Note: You can release the keylock by holding
down ENTER on the projector for about 5 seconds.
PRJ - ADJ1
Return
On
SEL. ENTER END
2
Select “On”, then press
ENTER
.
On-screen display
The Keylock function does not affect the
operation with the remote control buttons.
You cannot use the Keylock function while the
projector is warming up.
1
2
Taking the Keylock Off
Hold down ENTER on the projector for about
5 seconds.
On-screen display
Info
Even when Keylock function is set to “On”,
STANDBY/ON on the projector can be used
to turn on and off the power.
Keylock cannot be set while the projector is:
displaying the “Setup Guide” or “Menu”
screens, in Standby mode, warming up,
changing input signals, operating the Auto
Sync or Input Search function, in Freeze
mode or on the “System Lock” screen during
warming up.
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
(Continued)
Menu operation n Page 36
51
Useful
Features
Information on the 3D Projection Function
To display 3D images, this projector requires:
WHAT YOU WILL NEED
1) Source devices that support the field sequential format
– For details on the supported signals, see the Compatibility Chart in this operation manual.
2) 3D LCD shutter glasses that support the DLP
®
Link™* system
– Contact your nearest Sharp Authorized Projector Dealer for purchasing details.
* DLP
®
Link™ is a trademark of Texas Instruments.
The projected image may become dark when using the 3D projection function (with “DLP
®
Link™ ”
set to “On”).
When “DLP
®
Link™” is set to “On”, the following functions may not work fully or may not be
available at all.
– Keystone/Resize/Magnify
3D formats except for the field sequential method, such as ones used for Blu-ray 3D or DVD
prepackaged media, are not compatible with this projector. (As of March 2012)
If the power of your left and right eyes greatly differs and you primarily use one eye for viewing the
images, the images will not appear in 3D.
In addition, images may be difficult to view in 3D or images may not be able to be viewed in 3D
depending on the individual or the content being displayed.
The stereoscopic effect varies with the individual.
3D viewing is possible within the range that the 3D LCD shutter glasses are able to receive light
signals reflected by the screen. However, most 3D images are manufactured to be viewed from
directly in front of the screen, so 3D viewing is recommended directly in front of the screen as
much as possible.
– The range for receiving signals varies depending on the 3D LCD shutter glasses. For details, see
the operation manual of your 3D LCD shutter glasses.
3D images may not be able to be played back correctly on your computer.
Appendix
How the 3D Projection Function (DLP Link™ ) Works
The 3D projection function of this projector is compatible with the DLP
®
Link™ system. To watch
3D images, you use a pair of 3D LCD shutter glasses that alternately display the projected images
for the left and right eyes and are synchronized with a control (light) signal.
Shutter glasses
control light signal*
* The control light signal is transmitted from the lens of the projector, refl ected by the screen, and
received by the light reception sensor on the 3D LCD shutter glasses. Therefore, the range of 3D
viewing varies depending on the speci cations of the 3D LCD shutter glasses (light signal
receiving sensitivity).
For details, see the operation manual of your 3D LCD shutter glasses.
52
Using 3D Viewing Mode
Use the following procedure to project
3D images.
For operation of the 3D LCD shutter
glasses and the 3D-video playback
equipment, see the corresponding
operation manual.
O/Q buttons
ENTER button
3D MODE button
Projecting 3D images
1
Turn the projector on.
2
Turn the 3D-video playback
equipment on.
Set the 3D-video playback equipment so
that it outputs one of the signals listed in
the Compatibility Chart in this operation
manual.
3
Switch the Input mode of the
projector to enable input of 3D
video signals.
4
Operate the 3D-video playback
equipment and play back the 3D
content.
5
Turn the 3D LCD shutter glasses
on and place them over your eyes.
1
2
3
4
5
6
Press 3D MODE on the remote
control to display the 3D MODE
menu.
Info
If “An invalid button has been pressed.”
is displayed, a 3D-compatible signal is
not being input. Check the output signal
on the playback equipment.
7
Press Q to set “DLP
®
Link™” to
“On”.
8
Press ENTER to switch the mode
and enable more natural 3D
image viewing.
Warning!
If the projector, 3D-video playback
equipment, and 3D LCD shutter
glasses are not properly set, you may
experience eye strain in addition to not
being able to view the images in 3D.
9
Press 3D MODE.
The 3D MODE menu will disappear.
If the images are not displayed in 3D, repeat
steps 6 to 8.
You can also use “DLP
®
Link™” and “DLP
®
Link™ Invert” on the menu screen to change
the 3D setting.
Note
Ending 3D projection
1
Press 3D MODE on the remote
control to display the 3D MODE
menu.
2
Press O to set “DLP
®
Link™” to
“Off.
3
Press 3D MODE.
The 3D MODE menu will disappear.
6
7
8
9
1
2
3
Viewing Stereoscopic 3D Images (Continued)
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp PG-LW2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp PG-LW2000 in the language / languages: English as an attachment in your email.

The manual is 8,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp PG-LW2000

Sharp PG-LW2000 User Manual - German - 75 pages

Sharp PG-LW2000 User Manual - Dutch - 75 pages

Sharp PG-LW2000 User Manual - Italian - 75 pages

Sharp PG-LW2000 User Manual - Swedish - 75 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info