469851
64
Zoom out
Zoom in
Previous page
1/69
Next page
60
Problem Check Page
Maintenance indicator on
the projector illuminates
or blinks in red.
See “Maintenance Indicators”.
53
The projector cannot
be turned on or put into
the standby mode
using STANDBY/ON on
the projector.
The keylock is set.
If the keylock is set to “ON”, all the buttons are locked.
48
Picture is green on
COMPUTER
(Component)/
HDMI (Component).
Change the input signal type setting.
When you cannot select an input signal type, select “Color is faded or
poor” in the “Help” menu, after selecting an item other than “sRGB” in
“Picture Mode”, and then select an input signal type.
51
40, 51
Picture is pink
(no green) on
COMPUTER (RGB)/
HDMI (RGB).
Picture is too bright and
whitish.
Image adjustments are incorrectly set.
41
The cooling fan becomes
noisy.
When temperature inside the projector increases, the cooling fan runs
faster.
8, 9
52, 53, 5
4
The lamp does not light
up even after the
projector turns on.
The lamp indicator is illuminating in red.
Replace the lamp.
The lens shutter is closed.
53, 56, 57
The lamp suddenly turns
off during projection.
The image sometimes
fl i c k e r s .
Cables are incorrectly connected to the projector or the connected
equipment works improperly.
Select “Vertical stripes or fl ickering image appear” in the “Help” menu
and make the necessary adjustments.
If this happens frequently, replace the lamp.
21–25
51
56
The lamp needs much
time to turn on.
The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
56
Picture is dark.
One Touch Play/System
Standby is not enabled.
Non-Sharp Video Products are connected.
One Touch Play/System Standby function may not work when the
projector is connected to a non-Sharp Video Products.
37
An HDMI cable is not used for connection between the projector and
Sharp Video Products.
One Touch Play/System Standby function is enabled when the
projector is connected to Sharp Video Products with an HDMI cable.
22
One Touch Play/System Standby function of the projector is not set to
“On”.
37
CEC settings of connected Sharp Video Products are incorrect. 37
The remote control
cannot be used.
Operate the remote control while pointing it at the projector's remote
control sensor.
The remote control may be too far away from the projector.
If direct sunlight or a strong fl uorescent lamp is shining on the
projector's remote control sensor, place the projector where it will not
be affected by strong light.
15
The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
15
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5
minutes.
Troubleshooting (Continued)
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp PG-D40W3D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp PG-D40W3D in the language / languages: English as an attachment in your email.

The manual is 10,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp PG-D40W3D

Sharp PG-D40W3D User Manual - German - 35 pages

Sharp PG-D40W3D Installation Guide - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info