214299
11
Zoom out
Zoom in
Previous page
1/82
Next page
-7
Introduction
Be sure to read the following safeguards when setting up
your projector.
Caution concerning the lamp unit
Potential hazard of glass particles if
lamp ruptures. In case of lamp rupture,
contact your nearest Sharp Authorized
Projector Dealer or Service Center for
a replacement.
See Replacing the Lamp on page 65.
Caution concerning the setup of the projector
For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens must be cleaned more often. As long as the
projector is regularly cleaned, use in these environ-
ments will not reduce the overall operation life of the
unit. Internal cleaning should only be performed by a
Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places exposed to
direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colors, making viewing difficult. Close the cur-
tains and dim the lights when setting up the screen in a
sunny or bright room.
The projector may be safely tilted to a maximum
angle of 12 degrees.
Placement should be within ±12 degrees of horizontal.
Do not subject the projector to hard impact and/
or vibration.
Take care with the lens so as not to hit or damage the
surface of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will
cause eye strain. Be sure to occasionally rest your eyes.
Avoid locations with extremes of temperature.
The operating temperature of the projector is from 41°F
to 95°F (+5°C to +35°C).
The storage temperature of the projector is from
4°F to 140°F (20°C to +60°C).
Do not block the exhaust and intake vents.
Allow at least 7
7
/8 inches (20 cm) of space between
the exhaust vent and the nearest wall or obstruction.
Be sure that the intake vent and the exhaust vent are
not obstructed.
If the cooling fan becomes obstructed, a protection cir-
cuit will automatically put the projector into the standby
mode. This does not indicate a malfunction. Remove
the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where the in-
take and exhaust vents are not blocked, plug the power
cord back in and turn on the projector. This will return
the projector to the normal operating condition.
Caution regarding transportation of the projector
When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra care with the lens. Before moving
the projector, be sure to unplug the power cord from
the wall outlet, and disconnect any other cables con-
nected to it.
Do not carry the projector by holding the lens.
When transporting the projector, be sure to attach the
lens shipping block and the lens cap to the projector.
Other connected equipment
When connecting a computer or other audio-visual
equipment to the projector, make the connections AF-
TER unplugging the power cord of the projector from
the AC outlet and turning off the equipment to be con-
nected.
Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Using the projector in other countries
The power supply voltage and the shape of the plug
may vary depending on the region or country you are
using the projector in. When using the projector over-
seas, be sure to use an appropriate power cord for the
country you are in.
Temperature monitor function
If the projector starts to overheat
due to setup problems or blockage
of the air vents, and
will illuminate in the lower left cor-
ner of the picture. If the temperature continues to rise, the
lamp will turn off, the temperature warning indicator on
the projector will blink, and after a 90-second cooling-off
period the projector will enter the standby mode. Refer to
Maintenance Indicators on page 63 for details.
Info
The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
Do not unplug the power cord during projection or cool-
ing fan operation. This can cause damage due to rise
in internal temperature, as the cooling fan also stops.
BQC-PGB10S//1
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp pg b10s at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp pg b10s in the language / languages: English as an attachment in your email.

The manual is 7,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp pg b10s

Sharp pg b10s User Manual - German - 82 pages

Sharp pg b10s User Manual - Dutch - 82 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info