678911
65
Zoom out
Zoom in
Previous page
1/74
Next page
61
Anhang
STEUERUNGSINHALTE
Bereitschaft
Strom Ein
EINGANG 1
EINGANG 2
EINGANG 3
OK oder ERR
OK oder ERR
OK oder ERR
OK oder ERR
OK oder ERR
OK oder ERR
OK oder ERR
OK oder ERR
0~9999
P
P
I
I
I
I
I
I
T
A
A
A
L
S
S
S
T
I
I
I
T
0
1
2
1
O
O
R
V
V
W
W
G
E
E
R
R
B
D
D
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
1
1
2
BEFEHL
PARAMETER
RÜCKCODE
Verbleibende Lampen-Lebensdauer (Prozent)
Lampenstatus
Gerätestatus
Modellnamen-Prüfung
AV-Stmhalt Aus
AV-Stmhalt Ein
Auto-Sync-Start
0~100
0:Aus, 1:Ein, 2:
Neuversuch,
3:Warten, 4:
Lampenfehler
T
T
T
T
I
I
A
L
L
A
N
M
M
D
T
P
B
A
B
B
J
L
S
N
M
K
K
S
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
1
1
1
1
0
1
1
TASTEN- UND FERNBEDIENUNGSSCHLÜSSEL
PROJEKTORNAME
OK oder ERR
OK oder ERR
OK oder ERR
0: Normal, 1: Hohe Temp., 2: Gebläsefehler,
4: Filterabdeckungs-Fehler,
8: Lampen-Lebensdauer 5 % oder weniger,
16: Lampe ausgebrannt, 32: Lampe leuchtet nicht,
64: Temp. unnormal hoch
EINGANG 1 Signaltyp: Auto
EINGANG 1 Signaltyp: RGB
EINGANG 1 Signaltyp: Komponente
Lampen-Betriebsdauer (Stunden)
RS-232C-Spezifikationen und Befehlseinstellungen
POWR _ 1__
OK
Projektor
Computer
Hinweis
Wenn in der Tabellensparte Parameter ein Unterstrich (_) erscheint, geben Sie bitte
ein
Leerzeichen ein. Wenn ein Stern
(*) erscheint, geben Sie einen Wert innerhalb der in Klammern unter STEUERUNGSINHALTE angegebenen Spanne ein.
PC-Steuerung
Der Projektor kann durch einen Anschluss an einen Computer über ein serielles RS-232C-Steuerkabel (Kreuztyp, im Handel
erhältlich) über den Computer gesteuert werden. (Siehe Seite 20 Anschlussanleitungen.)
Kommunikationsbedingungen
Legen Sie die seriellen Porteinstellungen des Computers so fest, dass sie denen der Tabelle entsprechen.
Signalformat: Entspricht dem RS-232C-Standard. Paritätsbit: Keine
Baud-Rate: 9.600 Bps Stopp-Bit: 1 Bit
Datenlänge: 8 Bit Flusssteuerung: Keine
Grundformat
Computerbefehle werden in folgender Reihenfolge gesendet: Befehl, Parameter und Rückcode. Nachdem
der Projektor den Computerbefehl ausgeführt hat, sendet er einen Antwortcode an den Computer.
Info
Wird mehr als ein Code gesendet, dann wird jeder Befehl erst nach der Verifizierung des Empfangs der
Antwort für den vorangegangenen Befehl vom Projektor gesendet.
Hinweis
Wenn der Projektor in den Standby-Modus geschaltet wird, erscheint für etwa 20 Sekunden die Meldung “Ende. Warten.”.
Gleichzeitig wird, wenn der “POWR_ _ _1”-Befehl gesendet wird, “ERR” zurückgesendet und dieser Befehl wird nicht empfangen.
Befehle
Beispiel: Wenn der Projektor eingeschaltet wird, folgende Einstellung durchführen:
Problemantwort (Kommunikationsfehler oder inkorrekter Befehl)
Rückcode (0DH)
C1 C2 C3 C4 P1 P2 P3 P4
Antwortcodeformat
Normalantwort
O K
E R R
Befehl 4-stellig Parameter 4-stellig
Befehlsformat
Rückcode (0DH)
Rückcode (0DH)
PGA15X_G_PDF_P51_62.p65 04.11.4, 3:56 PM61
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp PG-A10X-A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp PG-A10X-A in the language / languages: German as an attachment in your email.

The manual is 4,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info