662067
11
Zoom out
Zoom in
Previous page
1/98
Next page
9
QUICK REFERENCE
Attaching the Stand
• Before attaching (or detaching) the stand, unplug the AC cord.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged.
CAUTION
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
After attaching the stand to the TV, do not hold the stand when you put up, set up, move or lay down the TV.
Do not remove the stand from the TV unless using a wall mount bracket to mount it.
5
The case is equipped with push-in tabs to hold
the cushioning materials in place. Push in the
tabs (2 for each location) to secure the cushioning
materials in the case.
Push-in tabs
6
After you have built the work table, spread a
blanket or similar soft cloth over the table and then
lay the TV display down on the covered table.
Do not use a small table for this.
Attaching the Stand to the TV
7
Insert the stand into the openings on the bottom of
the TV.
Make sure that the stand is fi rmly inserted into the TV.
Improper installation may result in tilting of the TV set.
8
Insert and tighten the 4 screws into the 4 holes on
the rear of the TV.
Short
screws
   
In the installation procedure, be careful not to catch your
ngers between the TV set and the fl oor.
Before attaching the stand to the TV, build a work
table on which to rest the TV.
To build the table, use the cushioning materials used in the
packaging.
TOP-C
FRONT
TOP-L
TOP-R
Of the cushioning materials used, TOP-C is also used
during stand unit assembly. Be sure to assemble the stand
unit before building the work table.
Stand Unit Assembly
1
Confi rm that there are 12 screws (8 long screws
and 4 short screws) supplied with the stand unit.
2
1
Set the post for the stand unit onto the TOP-C.
2
Attach the base to the post.
3
Insert and tighten the 8 screws into the 8 holes
on the bottom of the base.
Hold the stand unit securely with one hand, and then
tighten the screws.
  
FRONT
1
1
2
3
Long
screws
Building the Work Table
3
Attach the joints and close the case.
1
Insert a joint into the hole on the side of the case.
2
Pressing the tab, fi x the joint into place.
1
2
4
Insert each of the cushioning materials in the
respective directions shown in the fi gure.
Insert TOP-L and TOP-R into the left and right sides of
the case respectively.
Insert TOP-C to fi t between the lines on the other side
of the case.
TOP-L
TOP-R
JOINT
CASE
LINE
TOP-C
LC-90LE745U_E.indb 9LC-90LE745U_E.indb 9 2012/04/06 16:49:522012/04/06 16:49:52
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-90LE745U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-90LE745U in the language / languages: English as an attachment in your email.

The manual is 5,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info