475457
11
Zoom out
Zoom in
Previous page
1/48
Next page
Initial auto installation
When the TV is powered on for the first time after purchase,
the initial auto installation wizard appears. Follow the menus
and make the necessary settings one after another.
1 Press a on the TV.
• The initial auto installation wizard appears.
2 Setting the OSD language.
Press a/b/c/d to select the desired language.
3 Setting the country.
Press /// to select your country or area.
• This setting screen only appears during the initial auto
installation.
4 Select time zone.
5 Select broadcast settings.
Press / to select “Tuner type”. Press / to
select between differents tune type:
CADTV: Cable digital broadcasts.
ATV: Analogue broadcasts.
DTV: Digital broadcasts.
DTV + ATV: Digital and analogue broadcasts.
CADTV+ATV: Cable and analogue broadcasts.
SADTV: Satellite broadcasts.
SADTV + ATV: Satellite and analogue broadcasts.
6 Selecting the TV location.
Press / to select where you will use this TV, and
then press OK.
HOME: For domestic use.
STORE: DYNAMIC mode is predetermined. If the
Quick guide
Picture Mode is changed, the TV will automatically
switch back to DYNAMIC when there is no signal input
from the TV or remote control unit for 30 minutes.
If you have chosen STORE by mistake, go to Settings
Restore Factory Default OK, and the TV returns
to the initial screen.
7 Starting channel search.
Press to select Next and then press OK.
If you want to search for more broadcasts, execute
“DTV (or ATV, or CADTV) manual tuning” from the
menu “CHANNEL” (Page 22).
To watch both analogue broadcasts and digital
broadcasts, you should perform the channel search
setting “DTV+ATV” or “CADTV+ATV”.
Is not possible to search digital and cable digital
broadcasts at the same time.
8 The TV searches for, sorts and stores all the
receivable TV stations according to their settings
and the connected antenna.
To cancel the initial auto installation in progress, press
END.
NOTE
If you turn the power on the TV after performing step 4,
initial auto installation wizard does not appear. The auto
installation function allows you to execute the installation
again from the Channel menu (Page 22).
When "France" is selected in the Country setting, the PIN
code setting cannot be skipped.
After initial Auto Tuning is completed, the default PIN is
automatically set to “3001”. To change the PIN setting, refer
to Lock menu on page 21.
If you install a DVB-T/T2/S/S2 antenna for the first time
of relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
1 Press a channel you want to check.
2 Press MENU.
3 Press to select “Channel” menu and then press
OK.
4 Press / to select "Signal Information" and
then press OK.
5 Position and align the antenna so that the maximum
possible values for “Signal Strength” and “Signal
Quality” are obtained.
NOTE
The values of “Signal Strength” and “Signal Quality” indicate
when to check the appropriate alignment of the antenna.
Checking quality and
signal strength
Home
Store
9
Confirm the following before turning
on the power
E Is the antenna cable connected?
E Is the AC cord plugged in?
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-46LE730E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-46LE730E in the language / languages: English as an attachment in your email.

The manual is 9,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp LC-46LE730E

Sharp LC-46LE730E User Manual - Dutch - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info