567413
11
Zoom out
Zoom in
Previous page
1/35
Next page
English - 10 -
Standby Notications
If the TV does not receive any input signal (e.g. from
an aerial or HDMI source) for 5 minutes, the TV will go
into standby. When you next switch-on, the following
message will be displayed:
“TV switched to stand-by mode automatically
because there was no signal for a long time.”
Press OK to continue.
If the TV has been left on and not been operated for
a while, the TV will go into standby. When you next
switch-on, the following message will be displayed:
“TV switched to stand-by mode automatically
because no operation was made for a long time.”
Press OK to continue.
When the Auto TV OFF timeout is reached, the
following message will be displayed on the screen:
“Shut Down?”
Select Yes to shut down the TV. Select No to cancel.
The TV will switch off as well, if you do not make a
selection on this screen.
Using a Conditional Access Module
IMPORTANT: Insert or remove the CI module only when
the TV is SWITCHED OFF.
In order to watch certain digital channels, a conditional
access module (CAM) can be necessary. This module
must be inserted in the CI slot of your TV.
1. Obtain the Conditional Access Module (CAM) and
the viewing card by subscribing to a pay channel
company, then insert those to the TV using the
following procedure.
2. Insert the CAM and then the viewing card to the
slot that is located in the terminal cover at the
rear side of the TV.
3. The CAM should be correctly inserted, it is
impossible to insert fully if reversed. The CAM
or the TV terminal may be damaged if the
CAM is forcefully inserted.
4. Connect the TV to the mains supply, switch
on and then wait for few moments until the
card is activated.
5. When no module is inserted, “No Common
Interface module detected” message
appears on the screen.
You can refer to the module instruction manual for
details of the settings.
Note: It takes a few minutes to certify the licence key when
you insert a CA card into the CI+ compatible CI module for
the rst time. This process may fail when there is no antenna
input or you have never run “Auto installation”. If the old CAM
is used, authentication may fail. In such cases, contact the
contracted service provider.
CAM
module
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-40LE363EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-40LE363EN in the language / languages: English as an attachment in your email.

The manual is 7,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp LC-40LE363EN

Sharp LC-40LE363EN User Manual - German - 38 pages

Sharp LC-40LE363EN User Manual - Dutch - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info