567408
8
Zoom out
Zoom in
Previous page
1/35
Next page
English - 7 -
Connect Power
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
Antenna/Cable/Satellite Connection
Connect the aerial or cable TV plug to the AERIAL
INPUT (ANT.) or satellite lead to the SATELLITE
INPUT(LNB) located on the rear side of the TV.
“Satellite is only available in 362/363 series”.
Rear side of the TV:
SATELLITE
AERIAL
CABLE
Note: Satellite support is depending on the model.
(only available in LC-32LE363EN / LC-32LE362EN
/ LC-40LE363EN / LC-40LE362EN series)
Installing The Batteries Into The
Remote
Remove the back cover to reveal the battery
compartment.
Insert two size AAA batteries. Note the correct
polarity(+ or -). Do not mix old and new batteries.
Replace only with same or equivalent type.
Place the cover back on.
Angle of the remote control unit
Use the remote control unit by pointing it towards the
remote control sensor.
Objects between the remote control unit and sensor
may prevent proper operation.
Cautions regarding the remote control unit
Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit
to liquids, and do not place in an area with high
humidity.
Do not install or place the remote control unit under
direct sunlight. The heat may cause deformation
of the unit.
The remote control unit may not work properly if
the remote control sensor of the TV is under direct
sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote
control unit closer to the remote control sensor.
Switching On/Off
To Switch the TV On
Connect the power cord to the mains socket. Switch
the “ button on the TV to position “|” so the TV
will switch to standby mode. Then the standby LED
lights up.
To switch on the TV from standby mode either:
Press the “ ” button, P+ / P- or a numeric button
on the remote control.
Press the side function switch on the TV until the TV
comes on from standby.
The TV will then switch on.
To Switch the TV to Standby
To switch the TV to low power standby press the
” button on the remote control or press the side
function switch on the TV until the TV switches into
standby mode.
To Switch the TV Off
Switch the “ button on bottom of the TV to
position 2 as illustrated - “ ”, to isolate the TV from
the mains, the LED will go out.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-40LE362EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-40LE362EN in the language / languages: English as an attachment in your email.

The manual is 7,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp LC-40LE362EN

Sharp LC-40LE362EN User Manual - German - 38 pages

Sharp LC-40LE362EN User Manual - Dutch - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info