662066
32
Zoom out
Zoom in
Previous page
1/76
Next page
30
Watching TV
Auto power-off at a designated time
This function is conveniently used when, for instance,
going to bed while watching TV.
1
2
Sleep Timer: Remain 2 hr. 00 min.
NOTE
• The sleep timer indicator on the TV lights up when the time
has been set.
When the time has been set, countdown automatically starts.
• Five minutes before the preset of time expires, the
remaining time displays each minute.
• Select “Off” by pressing SLEEP to cancel the sleep timer.
Press SLEEP.
• Remaining time displays when sleep timer has
been set.
Each time you press SLEEP, the remaining
time switches as shown below.
0 hr. 30 min. 1 hr. 00 min. 1 hr. 30 min.
2 hr. 30 min. 2 hr. 00 min.
Off
Press MENU and the MENU screen displays.
1
Press
c
/
d
to select “Power Control”.
• Power control menu displays.
2
Press
a
/
b
to select “No Signal Off”, and then
press ENTER.
3
Press
c
/
d
to select “Enable”, and then press
ENTER.
• Five minutes before the power shuts down, the
remaining time displays every minute.
4
Press MENU and the MENU screen displays.
1
Press
c
/
d
to select “Power Control”.
• Power control menu displays.
2
Press
a
/
b
to select “No Operation Off”, and
then press ENTER.
3
Press
a
/
b
to select “30 min.” or “3hr.”, and
then press ENTER.
• Five minutes before the power shuts down, the
remaining time displays every minute.
4
NOTE
• “Disable” is the factory preset value.
Auto power-off when there are no
operations performed
You can set the TV to automatically power off when no
TV operation is performed for more than 3 hours.
NOTE
• “Disable” is the factory preset value.
When a TV programme finishes, this function may not operate.
Auto power-off after the end of broadcast
You can set the TV to automatically power off in about
15 minutes after the TV goes into a state of receiving no
programme signals, such as the end of a broadcast day.
Energy conservation settings
Press MENU and the MENU screen displays.
1
Press
c
/
d
to select “Power Control”, and
then press ENTER.
• Power control menu displays.
2
Press
a
/
b
to select “Ecology”, and then
press ENTER.
3
Press
c
/
d
to select “Yes”, and then press
ENTER.
4
Ecology
When set to “Yes”, the TV activates the following
power saving mode.
• “OPC” set to “On” (Page 34)
• “Standby Mode” set to “Mode2” (Page 30)
• “No Operation Off” set to “3hr.” (Page 30)
• “No Signal Off” set to “Enable” (Page 30)
Reducing the start-up time
You can reduce the TV’s start-up time after turning on
the power with the remote control unit.
Press
a
/
b
to select “Standby Mode”, and
then press ENTER.
3
Press c/d to select “Mode1” or “Mode2”, and
then press ENTER.
4
Press MENU and the MENU screen displays.
1
Press c/d to select “Setup”.
2
Selected item Description
Mode1* TV starting time is approximately 1
second from standby.
Mode2 Power consumption is less than 1W.
* Standby power consumption in Mode 1 setting is
approximately 28W.
NOTE
• Ecology mode cannot be deactivated by selecting “No”.
Each setting must be changed individually to deactivate
Ecology mode.
37D85X_en_d.indd 3037D85X_en_d.indd 30 9/29/2008 2:09:33 PM9/29/2008 2:09:33 PM
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-37D85X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-37D85X in the language / languages: English as an attachment in your email.

The manual is 12,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info