66383
26
Zoom out
Zoom in
Previous page
1/42
Next page
24
Programming recording (for logged in recorder)
You prepare the station marked with the  buttons for recording by
pressing the red button. In the following menu you con rm the timer
data or change them as required. Then a red dot is set in front of this
programme in the EPG programme list as an identi cation. If you select
this programme, you can delete the programme from the timer again
with the red button.
You can record a digitally transmitted programme and watch an analogue
programme at the same time or vice versa
.
Note: Never select the sound format “Dolby Digital” during recording,
even if this is provided, since it cannot be recorded.
Call EPG menu:
Note: not with DVB-T stations in UK.
Call EPG menu
EPG menu
Select provider
Station selection
AVL timer list
Data capture on (for DVB + analog)
You will nd the following settings in the EPG menu:
• “Select provider” • “Station selection” • “AVL timer list
• “Data capture”
Selection of provider/station
In case of analogue TV programmes, you can change the provider (the
station which transmits EPG data) to get EPG content for other pro-
grammes. You can do this under “Select provider”.
Select “Select provider” and call this menu with OK. If the station you
want to change to is not listed in the “Select provider” list, start the
provider search with the green button. This takes a while.
Or, if you know the station, press the yellow button for “Change provider
list”. Select the provider in the programme list and enter it with OK and
return to the provider selection with BACK.
Select the provider in the “Select provider” menu and press OK. Then a
programme range search is performed. The programmes offered by the
provider are displayed in a list.
If you want certain programmes to be omitted from the programme
guide, you can select and deactivate these in the "Station selection". Call
the programme selection with OK. Now all programmes are displayed
(the DVB programmes too). Programmes marked by “E” are analogue
terrestrial/cable programmes, programmes marked by “D” are digital
programmes ready for the programme guide. Select the programmes
you want to omit from the programme guide one after another and
deactivate each one with OK.
Data entry
After these settings or every time the switch is set off with the main
switch, the data must rst be collected (only for analogue TV). To do
this, select the programme which you have de ned as a provider and
leave it switched on for about 1 hour or switch the set to standby. After
about 2 minutes the mode indicator on the TV set lights orange. The
data entry begins and lasts about 1 hour. The data are also automatically
collected between 2 and 5 in the morning when the TV is switched to
standby.
A prerequisite for data entry is that “Data capture” is “on (for DVB +
analog)” in the EPG menu.
Note: If the main plug is pulled out or the ON/OFF-button is pushed, all
EPG data are lost.
If you cannot receive any EPG providers, for example, you should switch
off the data entry.
Switch on TV when marked
You can have the TV switched on automatically from standby at the be-
ginning of the memorised programme. If you are not present at the time,
a safety prompt makes sure the TV switches off again after 5 minutes.
Modes of operation
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-32GD7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-32GD7 in the language / languages: English as an attachment in your email.

The manual is 6,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info