66383

Sharp LC-32GD7 Manual

15
Zoom out
Zoom in
Previous page
1/42
Next page
13
Enter the appropriate channel number with the numeric buttons.
The corresponding bandwidth 7 or 8 MHz is set depending on the
channel and country.
Notes
:
You should only adapt the bandwidth if the channel spacing of the
stations in your area deviate from the standard.
If you receive a digital station, the signal quality (“C/N”) and the
signal strength level is displayed by a black bar/numeric value.
The antenna alignment or position is at an optimum when as high
a value as possible (large bar) is displayed for the signal quality
and signal strength.
The antenna should be aligned to give a maximum numeric
value/bar.
If no signal is found in the set channel, you can start the frequency
search within the selected band (VHF or UHF) by pressing the blue
button.
Check other channels on which digital stations are broadcast terrestri-
ally in your area one after another.
Align the antenna using the weakest station to as maximum as possib-
le a bar/numeric value.
Note: After the antenna has been positioned and aligned, we recommend
the “Automatic station programming” function to search for all stations
(see page 11).
New station search
This function is of particular advantage if you are only searching for new
stations.
Switch on your TV and if no menu is displayed, call the “TV menu” by
pressing the MENU button on the remote control
Select the ”Setup” item and confi rm with OK.
Caution:
Only if you use an active terrestrial antenna, switch on the supply volt-
age (5 Volt). See page 9 under "Antenna".
Select “Channels” and confi rm with OK.
Select “Search wizard” and confi rm with OK.
You will get a table for the automatic station search.
If required select “Change search settings” and confi rm with OK. Fol-
low the menus. Otherwise continue with step 10.
Select your “Location of TV set” and then indicate whether you are
searching via “Antenna/cable (analogue)”, “DVB-T” or in the “Satel-
lite 1: (DVB-S)” by marking the appropriate selection with the yellow
button.
6.
•
•
•
•
•
7.
1.
2.
3.
4.
5.
6.
In DVB-T you can select a channel search (fast station search) or a
frequency search.
Change search settings -> Signal source
Antenna/cable (analogue)
DVB-T
DVB-S
Indicate whether you wish to have “all” stations or “new ones only”
searched for.
Notes
:
The frequency search option is to be preferred only in exceptional
cases such as in the event of deviations from the standardized
channels.
If you have purchased a CI module, please insert it as described on
page 10.
Which of the stations of the provider you can watch in the end
depends on which station package you have bought.
To extend an existing station list we recommend you to activate
the option search and store “new ones only”.
For DVB-T stations in UK the stations are tied to “Logical Channel
Numbers” - „LCN“ and sorted from 1- 799. New digital stations
without “LCN” are stored from 800 onwards. Analogue stations
are stored behind the digital ones from 1001 onwards.
Confi rm your selection with OK.
Select the “TV/Color standard” for “Signal source”: “Antenna/cable
(analogue)“ and confi rm with OK.
Specify from which station place onwards the stations are to be
stored and confi rm with OK.
Select “Start search” and confi rm with OK.
The station search may take some time.
Do not make any entries or switch off the set during this time.
When the search has ended you will be shown the found and stored sta-
tions sorted in numerical order.
If you also want to search for and store analogue stations, repeat the
steps 5 to 10.
After the station search has been completed, close the table by pressing
the END button.
7.
•
•
•
•
•
8.
9.
10.
11.
First installation
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-32GD7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-32GD7 in the language / languages: English as an attachment in your email.

The manual is 6,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info