66383
11
Zoom out
Zoom in
Previous page
1/42
Next page
9
Cautions regarding the remote control unit
Do not expose the remote control unit
to shock.
In addition, do not expose the remote
control unit to liquids, and do not place
in an area with high humidity.
Do not install or place the remote con-
trol unit under direct sunlight. The heat
may cause deformation of the unit.
The remote control unit may not work
properly if the remote control sensor of
the TV is under direct sunlight or strong
lighting. In such case, change the angle
of the lighting or TV, or operate the
remote control unit closer to the remote
control sensor.
Connection
Power mains
Connect the TV set to a 220-240V/50–60 Hertz power outlet. Plug the
small plug of the power cable into the mains socket on the back of the
TV, the large plug into a wall outlet.
Antenna
Connect the antenna cable from your antenna/cable socket or the (room/
roof) antenna for DVB-T with the antenna socket “ANT-TV” on the back
of your TV set to receive digitally/terrestrially broadcast stations.
An indoor antenna can also be used under good reception conditions.
Passive and active room antennas are offered commercially. In an active
antenna its power is supplied via the antenna connection “ANT-TV”.
The “Supply voltage” (5 Volt) must be correspondingly set in the “TV
Menu – Connections–– Antenna DVB –– Antenna DVB-T”.
It is advisable to use an antenna without directional characteristic. If the
location is outside the normal transmission range, a directional antenna
(Yagi) can also be used to improve the reception quality.
You can obtain more detailed information about receivable digital sta-
tions in your area from your dealer.
You can also receive an analogue cable station or an analogue terrestrial
station and a satellite station * at the same time and watch with the
picture in picture (PIP) function.
Use the enclosed cable tie for laying the cables.
Remote control
To insert or change the batteries press on the arrow. Slide the battery
compartment cover downwards and remove it. Insert Alkali Mangan
LR 03 (AAA) batteries and ensure that the + and – ends are connected
correctly .
Then push the cover back on from the bottom until it snaps in.
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be
sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have
different characteristics.
Do not mix old and new batteries. Mixing old and new batteries can
shorten the life of new batteries or cause chemical leakage in old bat-
teries.
Remove batteries as soon as they have worn out. Chemicals that leak
from batteries can cause a rash. If you nd any chemical leakage, wipe
thoroughly with a cloth.
The batteries supplied with this product may have a shorter life
expectancy due to storage conditions.
If you will not be using the remote control unit for an extended period
of time, remove the batteries from it.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control
sensor. Objects between the remote control unit and sensor may prevent
proper operation.
30°
30°
m
7
t
eef 32
First installation
Remote control sensor
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp LC-32GD7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp LC-32GD7 in the language / languages: English as an attachment in your email.

The manual is 6,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info