141056
16
Zoom out
Zoom in
Previous page
1/28
Next page
14
Setup menu
Auto Installation
You can run Auto Installation again, even after setting
up the preset channels.
1 Press MENU and the MENU screen displays.
2 Press c/d to select Setup.
3 Press a/b to select Auto Installation, and then
press OK.
If you have already set the PIN under Child Lock,
enter it here.
See page 16 for setting PIN.
4 Press c/d to select Ye s , and then press OK.
5 You can set language and country the same as in
the initial auto installation. Follow steps 1 and 2
on page 7.
Programme Setup
This section describes how to set up analogue TV
channels manually.
Menu operations
MENU
[
Setup
]
Setup Option
Child Lock
Auto Installation
Programme Setup
Position
WSS
4:3 Mode [Panorama]
[On]
[English]Language
Auto Search
You can automatically search for and download TV
channels by performing the procedure below. This is
the same function as from programme auto search to
preset download in Auto Installation.
1 Repeat steps 1 to 4 in Programme Setup.
2 Press c/d to select Ye s , and then press OK.
1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download
1 Press MENU and the MENU screen displays.
2 Press c/d to select Setup.
3 Press a/b to select Programme Setup, and
then press OK.
If you have already set the PIN under Child Lock,
enter it here.
See page 16 for setting PIN.
4 Press a/b to select Auto Search, Manual
Adjust, Sort or Erase Programme, and then
press OK.
Auto Search
Manual Adjust
Sort
Erase Programme
No Yes
Power Control menu
No Signal Off
Menu Operation: A (page 11)
When set to “Enable” the TV will automatically enter
the standby mode if there is no signal input for 15
minutes.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
NOTE
• When a TV programme finishes, this function may not
operate.
MENU
[
Power Control
]
Audio Power Control
No Signal Off
No Operation Off
[Disable]
[Disable]
No Operation Off
Menu Operation: A (page 11)
When set to “Enable” the TV will automatically enter
the standby mode if no operations are performed for
3 hours.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
Power Management
Menu Operation: A (page 11)
When set, the TV will automatically enter the standby
mode.
Off: No power management
Factory preset value.
Mode1: If there is no signal input for 8 minutes, the TV
enters the standby mode.
Even if you start using the PC and the signal
inputs again, the TV stays in standby mode.
The TV turns on again by pressing a on the TV
or B on the remote control unit. (See page 7.)
Mode2: If there is no signal input for 8 seconds, the
TV enters the standby mode.
When you start using the PC and the signal
inputs again, the TV turns on.
The TV turns on again by pressing a on the TV
or B on the remote control unit. (See page 7.)
TV/AV only
TV/AV only
TV only
TV only
PC only
Item
LC-32SA1E_GB_b 06.7.25, 11:35 AM14
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp lc 26 sa1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp lc 26 sa1 in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info