745386

Sharp HT-SBW460 Manual

9
Zoom out
Zoom in
Previous page
1/52
Next page
EN
2. Activate your Bluetooth device and select the search mode.
“SHARP HT-SBW460” will appear on your Bluetooth device list.
If you cannot  nd the unit, press and hold the button on the remote
control or button on the unit to be searchable. The display will show
“PAIR” and you will hear "Pairing" from the unit.
3. Select “SHARP HT-SBW460” in the pairing list. After successful pairing,
you will hear "Paired" from the unit, and the display panel shows “BT”.
4. Play music from the connected Bluetooth device.
To disconnect the Bluetooth function, you can:
Switch to another function on the unit.
Disable the function from your Bluetooth device.The Bluetooth device
will be disconnected from the unit after the “Disconnected” voice
prompt.
Press and hold the button on the remote control or button on the
unit.
TIPS:
• Enter "0000" for the password if necessary.
• If no other Bluetooth device pairs with this player within two minutes,
the player will recover its previous connection.
• The player will also be disconnected when your device is moved beyond
the operational range.
• If you want to reconnect your device to this player, place it within the
operational range.
• I f the device is moved beyond the operational range, when it is brought
back, please check if the device is still connected to the player.
• If the connection is lost, follow the instructions above to pair your device
to the player again.
Listen to Music from Bluetooth Device
If the connected Bluetooth device supports Advanced Audio Distri-
bution Pro le (A2DP), you can listen to the music stored on the device
through the player.
If the device also supports Audio Video Remote Control Pro le (AVRCP),
you can use the player's remote control to play music stored on the
device.
1. Pair your device with the player.
2. Play music via your device (if it supports A2DP).
3. Use supplied remote control to control play (if it supports AVRCP).
To pause/resume play, press the button on the remote control or
on the unit.
To skip to a track, press the / buttons on the remote control.
USB
USB Operation
1. Insert the USB device.
2. Press the button repeatedly on the unit or press the button on
the remote control to select USB mode.
3. During playback:
To pause or resume play, press the button on the remote control or
on the unit.
To skip to the previous/next  le, press the / buttons on the
remote control.
TIPS:
• USB devices up to 32GB are supported.
• Only MP3  les can be played back.
Troubleshooting
No power
• Ensure that the AC cord of the soundbar and subwoofer are correctl
connected.
• Ensure that there is power at the AC outlet.
• Press (standby) button to turn the unit on.
Remote control does not work
• Before you press any playback control button,  rst select the correct
source.
• Reduce the distance between the remote control and the unit.
• Insert the battery with its polarities (+/-) aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the sensor on the front of the unit.
No sound
• Make sure that the unit is not muted. Press MUTE or VOL+/VOL– button
to resume normal listening.
• Press button on the unit or on the remote control to switch the soundbar
to standby mode. Then press the button again to switch the soundbar
on.
• Unplug both the soundbar and the subwoofer from the mains socket,
then plug them again. Switch on the soundbar.
• Ensure the audio setting of the input source (e.g. TV, game console, DVD
player, etc.) is set to PCM or Dolby Digital mode while using digital (e.g.
HDMI, OPTICAL, COAXIAL) connection.
• The subwoofer is out of range, please move the subwoofer closer to the
soundbar. Make sure the subwoofer is within 5 m of the soundbar (the
closer the better).
• The soundbar may have lost connection with the subwoofer. Re-pair
the units by following the steps on the section “Pairing the Wireless
Subwoofer with the Soundbar”.
• The unit may not be able to decode all digital audio formats from the
input source. In this case, the unit will mute. This is NOT a defect.device
is not muted.
TV has display problem while viewing HDR content from HDMI source.
• Some 4K HDR TVs require the HDMI input or picture settings to be set for
HDR content reception. For further setup details on HDR display, please
refer to the instruction manual of your TV.
I can’t  nd the Bluetooth name of this unit on my Bluetooth device for
Bluetooth pairing
• Ensure the Bluetooth function is activated on your Bluetooth device.
• Ensure you have paired the unit with your Bluetooth device.
This is a 15 mins power off function (ERPII standard requirement for
saving power)
• When the unit's external input signal level is too low, the unit will be
turned o automatically in 15 minutes. Please increase the volume level
of your external device.
The subwoofer is idle or the indicator of subwoofer does not light up.
• Please unplug power cord from the mains sockect, and plug it in again
after 4 minutes to resent the subwoofer.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp HT-SBW460 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp HT-SBW460 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 6,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info