459674
21
Zoom out
Zoom in
Previous page
1/92
Next page
ENGLISH
FRANÇAIS
NEDERLANDS
DEUTSCH
E-19
TROUBLESHOOTING
Before calling for repair, please review the list below, since the problem may not be a unit malfunction.
SYMPTOM
REMEDY (not a malfunction)
The Remote Control does not
work.
• Have the batteries been depleted?
• Are the batteries inserted correctly?
Is a fluorescent lighting in the room flickering due to service
life?
Odours and smoke are not
removed.
• Clean or replace the filters if they appear to be heavily soiled.
(Refer to E-16,E-18)
The CLEAN-SIGN Light lights
green even when the air is
impure.
The air could be impure at the time the unit was plugged in.
(Refer to E-12)
Pull out the plug from the electrical outlet, and insert the plug
one minute later.
The CLEAN-SIGN Light lights
orange or red even when the air
is clean.
The sensitivity of the sensors become unstable when the
opening of the odour sensor or dust sensor is dirty or is clogged.
Clean the dust around the sensor opening using a vacuum
cleaner. (Refer to E-17)
When in Clean Mode, the Plasmacluster Indicator Light colour
will not change.
A clicking or ticking sound is
heard from the unit.
Clicking sound or ticking sound is emitted when the unit is
generating ions.
The discharged air has an
aroma or odour.
Check to see if the filters are heavily soiled.
Replace the filters.
Plasmacluster Air Purifiers emit small traces of ozone which
may produce an odour. These ozone emissions are well below
safety levels.
The Plasmacluster Indicator
Light remains blue and does
not change.
The unit does not operate when
cigarette smoke is in the air.
Is the unit installed in a location that is difficult for the sensor to
detect cigarette smoke?
• Are the dust or odour sensor openings blocked or clogged?
(In this case, clean the openings.) (Refer to E-17)
The MIST Unit Indicator Light
remains activated even after
replacing filter.
• After replacing filters, connect the power cord to an outlet and
press the Mist Unit Reset Button. (Refer to E-15)
The Plasmacluster Indicator
Light or the CLEAN-SIGN Light
will not activate.
Check to see if the Lights OFF Mode on the Remote Control is
selected. If so, then press the Lights ON/OFF Button on the
Remote Control to activate the indicator lights.
(Refer to E-11)
(Care Cycle : MIST Filter : 1 month)
Plasmacluster Indicator Light
repeat colour cycles between
blue and green.
Mist Unit Indicator Light does not
turn on even water is in.
When the water of the tank does
not decrease or the decrease of
the water is slow.
• The ION SHOWER operation is working.
Check to see if the Mist Unit and Tank are installed correctly.
Check the Mist Filter. Replace the filter when it is heavily soiled.
(Refer to E-14,18)
Please check if the impurities adhered to the surface of the
Float.
Clean the Mist Tray.
Check to see check if the Main Unit is put on a inclined surface.
The CLEAN-SIGN LIGHT switches
frequently.
The CLEAN-SIGN Light will automatically switches the colours
when detected by dust and odour sensors.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp FU-S63E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp FU-S63E in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 14,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sharp FU-S63E

Sharp FU-S63E User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info