770372
13
Zoom out
Zoom in
Previous page
1/14
Next page
Phenomenon Possible reason and solution
Program stops during WASH/RINSE mode Water detector is working, it is normal.
Water inlet during WASH/RINSE mode Water detector detects low water level, inlet water automatically.
Program stop after WASH/RINSE mode Spin mode delay, it is normal.
When spinning, tub rotates discontinuously Program designated to be intermittently paused.
During SPIN mode, tub knocking and water start supply and
enter RINSE mode
Unbalance spinning causes program to autocorrect and resume, it is
normal.
Sounds of water flowing after SPIN mode end It is the sound of the fluid inside balance ring, it is normal.
Control panel heating up The memory part of PWB heating up, it is normal.
Operation button not working Press too soft.
SAFETY LOCK mode is on, deselect it.
Troubleshooting
Some of the circumstances may not be a
please contact our service department, do not try to disassemble the washer or repair the washer
by yourself.
fault, please check before sending for repairs. If it is a fault,
Display Problem Solution Reason Summary of
Reason
Water supply is too low.
Water faucet is shut off.
Filter net of water Inlet valve
jammed.
Increase water supply.
Turn on the water faucet.
Wash the filter net, remove blockage,
press the START/PAUSE button.
①②
③④
⑤⑥
Pipe leaking
PWB
breakdown
Inlet valve
breakdown
Circuit board
breakdown
Connection of
control panel
loosen off
Water level
sensor breakdown
Safety lock
breakdown
Drainage system
breakdown
Retractor
breakdown
Connection of
retractor loosen off
Water level exceeded the highest
limit of the tub.
Abnormal water level.
Program will automatically adjust the
water level and resume function.
②④
⑤⑥
Lid open when running PRESET
mode.
Lid do not close when Spin mode is
operating.
Close the lid. ②④
⑤⑦
Washing machine incline.
Clothes is collected on one side,
causing unbalanced spin.
Adjust the adjustable leg.
Open the lid and distribute the clothes
evenly.
④⑤
Draining position is relatively high.
Drainage hose is frozen or blocked.
Drainage hose is bent, squeezed,
tangled.
Lower down the drain hose, press
START/PAUSE button.
Defreeze/unblock drainage hose, press
START/PAUSE button.
Smooth out drainage hose, press
START/PAUSE button.
②④
⑤⑥
Lid do not close when safety lock is
on.
Close the lid in 10s and program will
resume itself; if lid is still open after 10s,
machine will start draining. To resume,
deselect SAFETY LOCK mode.
②④
⑤⑦
Common non-fault phenomenon
13
E1
E2
E3
E4
E5
E7
55
16
注意
CAUTION:
13
重量 比例
14
宁波新乐电器有限公司
批准
会签
审核
标记处数 更改文件号
分区
设计
校对
制图
工艺
标准
341 2
D
AA
BB
CC
341 2
A
128克铜版纸
说明书
颜色
颜色 B
A
颜色
旧底图总号
技术要求:
1、商标:SHARP
2、尺寸:254X190.5mm
3.其余符合QB/XL20产品说明书技术标准
图文均为黑色
ESX705
Q6012P01SMSWJ
Q6012P01SMSWJ
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sharp ESX115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sharp ESX115 in the language / languages: English as an attachment in your email.

The manual is 5.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info